Yamaha 30DMH Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 66

background image

Operation

26

EMU27120

Oil

●

Check to be sure you have plenty of oil for
your trip.

EMU27140

Engine

●

Check the engine and engine mounting.

●

Look for loose or damaged fasteners.

●

Check the propeller for damage.

EMU36952

Install cowling

1.

Be sure that a cowling lock lever is re-
leased.

2.

Be sure that the rubber seal is seated all
the way around the engine.

3.

Place the cowling on top of the seal.

4.

Check to be sure the rubber seal fits cor-
rectly all the way around the engine.

5.

Move the lever to lock the cowling as
shown.

NOTICE:

If the cowling is not

installed correctly, water spray under
the cowling can damage the engine,
or the cowling can blow off at high
speeds.

[ECM01990]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

EMU27234

Filling fuel and engine oil

EMU27246

Filling fuel for portable tank

WARNING

EWM01830

●

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

●

Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately. If gasoline spills

1. Clip
2. Cord
3. Engine shut-off switch

1

2

3

ZMU03759

ZMU06117

ZMU04678

«
...
29
30
31
32
33
...
»

Summary of Contents for 30DMH



































































Reviews:

No comments

Related manuals for 30DMH

Brand: M5Stack Pages: 16

Brand: Yamaha Pages: 86

Brand: MPS Pages: 6

Brand: QDI Pages: 85

PP-I7RS400 PURE PERFORMANCE II

Brand: Sapphire Audio Pages: 44

Brand: JETWAY Pages: 48

Brand: Linear Pages: 6

Brand: Seanix Pages: 49

Brand: Lite-on Tech Pages: 49

Brand: Safran Pages: 29

Brand: Zeal-All Pages: 8

Brand: Gigabyte Pages: 120

BOOSTXL-DRV8301

Brand: Texas Instruments Pages: 13

OPTIREG PMIC TLF30682QVS01

Brand: Infineon Pages: 24

Brand: Texas Instruments Pages: 13

Brand: Advantech Pages: 6

Brand: TYAN Pages: 52

K8M800 INFINITY

Brand: DFI Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands