Yamaha 210FSH SPORT 2020 Operator'S Manual Download Page 63

Page: 63 / 146

Equipment operation

Removable backrest (210FSH SPORT/
210FSH DELUXE)

This boat has 2 removable backrests.

Backrest

Engine hood

The engine hood can be opened to access
the engine.
The engine hood latches are located under
the front of the leaning post.
To open the engine hood, pull the engine
hood latches up and lift the engine hood.

NOTICE:

Do not open the engine hood

while the anchor light is installed.
(210FSH DELUXE) Otherwise, the anchor
light could be damaged.

Engine hood latch

Engine hood

To close the engine hood, push the leaning
post to securely lock it in place.

SportsBoat_F4A12.book Page 56 Tuesday, May 28, 2019 10:42 AM

Summary of Contents for 210FSH SPORT 2020



















































































































































Search results

Summary of Contents for 210FSH SPORT 2020

Reviews:

Related manuals for 210FSH SPORT 2020

Brands by name

Popular brands

Yamaha 210FSH SPORT 2020, Operator'S Manual

Search results

Summary of Contents for 210FSH SPORT 2020

Reviews:

Related manuals for 210FSH SPORT 2020

Brands by name

Popular brands