Yamaha 2008 YZF-R1X Page 21 Owner'S Manual Download | Manualshive

Page: 21 / 108

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-5

3

NOTE:

This model is also equipped with a self-
diagnosis device for the fuel level de-
tection circuit. If the fuel level detection
circuit is defective, the following cycle
will be repeated until the malfunction is
corrected: The fuel level warning light
will flash eight times, and then go off for
3.0 seconds. If this occurs, have a
Yamaha dealer check the vehicle.

EAU11423

Coolant temperature warning
light “

”

This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir-
cuit.

CAUTION:

ECA10020

Do not operate the engine if it is
overheated.

U4C821E0.book Page 5 Tuesday, July 17, 2007 11:37 AM

«
...
19
20
21
22
23
...
»

Summary of Contents for 2008 YZF-R1X













































































































Reviews:

No comments

Related manuals for 2008 YZF-R1X

Brand: Ducati Pages: 123

Fastrax 50144-00

Brand: Dowco Pages: 3

Easyrack 6617501 01 01

Brand: hepco & becker Pages: 4

690 Enduro R AU/GB 2014

Brand: KTM Pages: 18

Brand: Honda Pages: 41

Brand: Cycle Protect Pages: 15

Brand: MOTO GUZZI Pages: 209

Brand: Husqvarna Pages: 12

Brand: Husqvarna Pages: 12

Brand: Husqvarna Pages: 7

Brand: Husqvarna Pages: 32

Brand: Husqvarna Pages: 7

Brand: Husqvarna Pages: 128

POCKET BIKE QG-40

Brand: Coolster Pages: 13

Brand: REV'IT Pages: 48

Brand: hepco & becker Pages: 3

Brand: KFI Pages: 2

Brand: Kinroad Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands