Yamaha 2005 YZF-R1T Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 106

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-15

3

EAU12870

Shift pedal

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed con-
stant-mesh transmission equipped on
this motorcycle.

EAU33850

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.
The brake lever is equipped with a po-
sition adjusting knob. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting knob
while holding the lever pushed away
from the handlebar grip. When the de-
sired position is obtained, be sure to set

it by aligning a groove on the adjusting
knob with the “

” mark on the brake

lever.

1. Shift pedal

1. Brake lever

2. Brake lever position adjusting knob

3. Distance between brake lever and handlebar

grip

4. “

” mark

U5VY21E0.book Page 15 Friday, September 10, 2004 9:21 AM

«
...
29
30
31
32
33
...
»

Summary of Contents for 2005 YZF-R1T











































































































Reviews:

No comments

Related manuals for 2005 YZF-R1T

Brand: Free Spirits Pages: 32

Brand: Keis Pages: 2

Brand: Öhlins Pages: 2

Mechatronics 35007-01

Brand: Öhlins Pages: 4

McPherson Strut MIR 5H02

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 4

Brand: MadStad Engineering Pages: 8

Brand: Honda Pages: 161

Brand: Honda Pages: 98

Brand: Yamaha Pages: 60

Brand: Yamaha Pages: 112

Brand: Honda Pages: 130

Brand: hepco & becker Pages: 6

Brand: FMF Pages: 4

Brand: Petzl Pages: 3

Brand: Petzl Pages: 11

Brand: Petzl Pages: 11

RR 4T ENDURO 2014 350

Brand: Beta Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands