background image

– 18 –

FI

FUEL INJECTION SYSTEM

24

No normal signals are received from 
the O

2

 sensor.

• Open or short circuit in wiring harness.
• Defective O

2

 sensor.

• Malfunction in ECU.
• Improperly installed sensor.

30

The motorcycle has overturned.

• Overturned.
• Malfunction in ECU.

08

31

The amount of air-fuel ratio feedback 
compensation is maintained continu-
ously in the vicinity of the upper limit 
(lean air-fuel ratio).

• Open or short circuit in wiring harness.
• Fuel pressure too low.
• Clogged injectors.
• Defective O

2

 sensor (unable to output a rich signal).

• Malfunction in ECU.
• Malfunction in other areas of the fuel system.

32

The amount of air-fuel ratio feedback 
compensation is maintained continu-
ously in the vicinity of the lower limit 
(rich air-fuel ratio).

• Open or short circuit in wiring harness.
• Fuel pressure too high.
• Faulty injectors (excessive injection volume).
• Defective O

2

 sensor (unable to output a lean signal).

• Malfunction in ECU.
• Malfunction in other areas of the fuel system.

33

Open circuit is detected in the primary 
wire of the ignition coil (#1, 4).

• Open or short circuit in wiring harness.
• Malfunction in ignition coil.
• Malfunction in ECU.
• Malfunction in a component of ignition cutoff circuit system.

30

34

Open circuit is detected in the primary 
wire of the ignition coil (#2, 3).

• Open or short circuit in wiring harness.
• Malfunction in ignition coil.
• Malfunction in ECU.
• Malfunction in a component of ignition cutoff circuit system.

31

41

Lean angle cut-off switch - open or 
short circuit detected.

• Open or short circuit in wiring harness.
• Defective lean angle cut-off switch.
• Malfunction in ECU.

08

42

No normal signals are received from 
the speed sensor; or, an open or 
short circuit is detected in the neutral 
switch.

• Open or short circuit in wiring harness.
• Defective speed sensor.
• Malfunction in vehicle speed sensor detected unit.
• Defective neutral switch.
• Malfunction in the engine side of the neutral switch.
• Malfunction in ECU.

07
21

43

The ECU is unable to monitor the bat-
tery voltage (an open circuit in the 
monitor line to the ECU).

• Open circuit in wiring harness.
• Malfunction in ECU.

44

An error is detected while reading or 
writing on EEPROM.

• Malfunction in ECU. (The CO adjustment value is not prop-

erly written on or read from the internal memory).

60

50

Faulty ECU memory. When this mal-
function is detected, the code number 
might not appear on the meter.

• Malfunction in ECU. (The program and data are not properly 

written on or read from the internal memory.)

Code No.

Symptom

Probable cause of malfunction

Diagnostic code

Summary of Contents for 2004 FJR1300(S)













































Reviews: