background image

1/2 

 

 

- Preface 

Thank you for purchasing a Yamada product. HR series Hose Reels are spring-driven and ceiling-, wall-, or floor 
mounted hose reels used to supply air, oil, grease, water, and warm water at various sites such as maintenance 
factory or gas station. 
Built-in ratchet mechanism locks the reel at desired hose length. You can wind up the supply hose onto the reel drum 
by drawing it a little further so that it will not get in the way when not in use. 
 

-  For Safe Operation 

This manual describes the items that are important for the user to operate this product safely, correctly, and efficiently. 
Before operating this product, read this manual thoroughly, in particular, “Warnings and Cautions” at the beginning of 
this manual. 
 

-  Warnings and Cautions 

For safe use of this product, be sure to note the following: In this document, warnings and cautions are indicated by 
symbols. These symbols are for those who will operate this product and for those who will be nearby, for safe 
operation and for prevention of personal injury and property damage. The following warning and caution symbols 
have the meanings described below. Be sure to remember their meanings. 
 

WARNING 

This indicates the existence of potential hazard which, if not avoided, will 

result in death or serious injury. 

CAUTION : 

This indicates the existence of potential hazard which, if not avoided, may 

result in bodily injury or in physical damage. 

Furthermore, to indicate the type of danger and damage, the following symbols are also used along with those 
mentioned above: 

   

This symbol indicates a DON'T, and will be accompanied by an explanation on something you must not 
do.  

 

This symbol indicates a DO, and will be accompanied by instructions on something you must do in a 
certain situation. 

 

-  Precautions on Use 

The following warnings and cautions are very important. Be sure to observe them. 

WARNING 

-  Never make modifications to the product. Unauthorized modifications could result in physical injury and 

accidents, as well as degraded functionality.

 

-  Do not use with gasoline, kerosene, or other solvents. It can cause severe injury, property damage, or 

product malfunction. 

-  If the service hose has difficulty rewinding, request services from your dealer. Reckless disassembly 

could cause the powerful spiral spring to eject, causing serious physical injury. 

-  Some oils and greases can cause skin inflammation. 

Thoroughly read the handling precautions for oil and grease provided by a supplier before use. 

-  When rewinding the service hose, do not release it at once. The gun attached to the hose end could 

violently swing to left and right when the hose rolls up, resulting in property damage or physical harm. 
Handle the service hose with maximum care. 

-  HR series hose reels have a specified allowable fluid temperature and maximum working pressure. 

Using the hose reel beyond the specifications may wear out packings and hoses. Any secondary 
accidents such as body injury or facility contamination caused by ignoring the instructions are the user’s 
responsibility. 

 

 

Summary of Contents for HR Series

















Reviews: