About the Guide
Operating with Yale View app
Installing
Camera
Step 2
Scan the following QR code or search Yale View app in Google Play or App
Store to download and install the Yale View app.
Step 5
Step 4
Connect your smart phone to your Wi-Fi network, and make sure that
your smartphone is connected to Wi-Fi network with 2.4 GHz band, then
follow the in app instructions to complete finishing setting up the camera.
Run the Yale View app, and then register an account for first use.
Step 3
Wait for the camera to finish the booting cycle, and then the camera indicator
flashes with a green light.
Note
If your Wi-Fi network changes or the indicator status changes,
reset the camera and re-do the setup from step 5 to add it again.
If you have more than one camera, do step 5 to add them one
by one.
Disclaimer
Using the hook provided, hook one end of the hook into the hole on the
mounting box, and the other end to the edge of the camera, so you
can use both hands to complete the installation.
Step 7
Adjust the light and lens angle, and keep the PIR detector parallel
to the ground to ensure optimal detection.
Step 1
Power on the camera.
Step 3
Put away all the wires, attach the camera to the mounting box, and
fix the camera with mounting screws and apply the screw cover to
the mounting box.
Step 4
Step 1
If there is no holes in the wall, insert the drilling template where
you want the floodlight camera to be installed. Using the drill
template as a guide drill the two parallel holes on the wall, add the
wall plugs and move to the next step.
Note
If you have installed the app, update it to the latest version.
This guide is for informational purpose only. Working with electricity
can be dangerous unless proper safety precautions are taken. If you
are not comfortable or are inexperienced with the processes and tools
described in this manual, we strongly suggest that you hire a licensed
electrician.
All the design and software here are subject to change without prior
written notice.
All trademarks and registered trademarks mentioned are the prop-
erties of their respective owners.
Please visit our website or contact your local service engineer for more
information.
If there is any uncertainty or controversy, please refer to our final
explanation.
-
-
-
-
Be sure to disconnect the power at the fuse or circuit breaker before
installation.
Always follow code standards when installing wired connection.
Verify that the supply voltage is correct. Connect fixture to a
100–240VAC 50/60 Hz power source.
We strongly suggest that you hire a licensed electrician to install the
camera.
Risk of fire
Do not install the camera near combustible or flammable surfaces.
Note
Do not connect this light fixture to a dimmer switch or timer.
Make sure that the mounting surface is strong enough to hold at
least three times of the device weight.
-
-
-
-
-
-
Risk of electrical shock
WARNING
Step 8
For permanently connected equipment, a readily accessible
disconnect device shall be incorporated external to the equipment.
-
For pluggable equipment type B or permanently connected
equipment, the maximum rating of an overcurrent protective
device to be provided external to the equipment is 20A.
-
Step 2
Turn the adjusting knobs to loosen the lights, and adjust the light
angles to give space to the mounting screw. Loosen the mounting
screw to open the mounting box, and then loosen the screw on the
ground terminal to remove the ground wires.
Attach the mounting box to the wall with the self-tapping screws,
making sure the UP arrow is in the correct position.
Step 5
L
N
Connect the two removed yellow and green striped wire (ground
wires) to the ground terminal again, tighten the screw on the ground
terminal, and then put back the terminal board with the insulating
gasket in the mounting box.
Step 6
Take out the terminal block from the mounting box. Connect the blue
wires (neutral wires) to the terminals N, and the brown wires (live
wires) to terminals L, and then the yellow and green strip wire to
ground terminal on the board.
Part of ASSA ABLOY
