P
P
o
o
w
w
e
e
r
r
S
S
a
a
v
v
i
i
n
n
g
g
F
F
e
e
a
a
t
t
u
u
r
r
e
e
:
:
When idle, KP-Y7 is in “
standby
” mode and uses sleep mode. It will activate and “
wake-up
” for 5 seconds where any key is pressed.
After 5 seconds of key inactivity, the power goes off and it returns to Stand-by mode.
Upon completion of a command input, the power goes off and KP-Y7 returns to Stand-by mode.
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
K
K
P
P
-
-
Y
Y
7
7
KP-Y7 is designed to be able to sit in a cradle when unused. The cradle has mounting holes to be mounted on a wall as shown on the
diagram on the left below.
When KP-Y7 is unused, it can be inserted into the cradle and covered by the cradle cover as shown on the diagrams on the right below.
Mounting the Cradle
Inserting KP-Y7 into Cradle
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
t
t
h
h
e
e
C
C
r
r
a
a
d
d
l
l
e
e
Using the 2 mounting holes as a template, mark off the positions at the desired mounting surface.
Insert the wall plugs if fixing into plaster or brick surface.
Screw the cradle onto the wall plugs.
T
T
e
e
s
s
t
t
m
m
o
o
d
d
e
e
:
:
KP-Y7 can be put into Test mode by pressing
Function Button 1
and then entering the KP-Y7 PIN code (Default:
0000
) first. LED will
start to flash.
To exit Test mode, press the
Disarm button
twice, the LED will stop flashing. Alternatively, KP-Y7 will automatically exit Test mode
after 5 minutes of inactivity and return to Standby mode.
Test mode enables the following functions:
Transmit KP-Y7 learn signal
— “
Function button 1
“ > “
1
”
Change the Pin Code
— “
Function button 2
” >
“New PIN code
” > “
Arm button
”
Exit Test Mode
— Press
Disarm button
twice
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
P
P
r
r
o
o
c
c
e
e
d
d
u
u
r
r
e
e
s
s
:
:
Step 1.
Remove the Battery Insulator.
Step 2.
The LED will turn on for 5 seconds as the KP powers up.
Step 3.
Learning KP-Y7 into the Control Panel:
I. Put the Control Panel into Learning Mode (Please refer to the manual of Control Panel).
II. Press the numeric key “
8
” + “
9
” to transmit a learn code. The LED will flash quickly for 2 seconds.
III. If the Control Panel successfully receives the learn code, refer to the manual of the Control Panel to complete the learn-in
process.
<
<
N
N
O
O
T
T
E
E
>
>
KP-Y7 can also transmit a learn code by pressing the
Function Button 1
followed by
numeric key 1
during Test Mode.
Step 4.
To check for signal strength of KP-Y7 at a desired mounting site, put the Control Panel into its range test (
Walk Test
) mode.
Step 5.
Hold the KP-Y7 at the desired location, press & hold Numeric key “
8
+
9
” to transmit a learn code. The RSSI signal strength value
will be displayed (e.g. on LCD display or web configuration page), the value ranges from 0-9 (9 indicates the best signal strength
performance).
<
<
N
N
O
O
T
T
E
E
>
>
It is recommended to install KP-Y7 at a site with a RSSI value of 5 or greater.
Step 6.
When you are satisfied that the KP-Y7 works in the chosen location, you can proceed with mounting the KP-Y7 following the steps
described in
Mounting KP-Y7
.
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
O
O
v
v
e
e
r
r
v
v
i
i
e
e
w
w
:
:
Arm
— Press the
Arm button
once
Home Arm
— Press the
Home Arm button
once
