background image

Page 11

INSPECTOR’S REPORT

Item

Remarks (List Deficiencies and Recommended Action)

Inspector’s

Signature

                Date
                Inspected                                   Approved By                                                     Date

Figure 4-2 Recommended Inspector's Report

4-3. Load Brake Function Check

To check the functioning of the mechanical load brake, proceed
as follows:

a. Attach a light load to the hoist and lift it several inches.

b. Disconnect Hoist From Power Supply and remove short

end brake cover (see Figure 8-1, Index No. 1).

c. Referring to Figure 4-3 and Figure 8-9, place screwdrivers

No. 1 and No. 2 behind the plate and armature assembly
and prepare to pry against the transmission cover.

Note

Do not allow either screwdriver to contact brake disc (see
Figure 8-9, Index No. 7).

d. Carefully pry open motor brake (close solenoid gap) and

observe action of load. If the load accelerates, the
mechanical load brake is malfunctioning and must be
repaired.

Figure 4-3 Load Brake Function Check List

14019

For more information contact: Sievert Crane and Hoist, (708) 771-1600, [email protected], www.sievertcrane.com

Summary of Contents for LEW-1 Series

































































Reviews: