2
)
F
lush
M
ount
I
nstallatIon
1. Remove the
MLS-310
from the bracket by removing
the two Mounting Bracket Knobs, then remove the rear
case of the
MLS-310
from the main body by removing
the four screws (Figure 3.).
2. Assemble the supplied M4x50 Screw, Nut, and Washer
as the Figure 4.
3. Use the supplied template to mark the location where
the round hole is to be cut. Confirm the space behind the
dash or panel is deep enough to accommodate the
MLS-
310
(at least 4.3 inch (110 mm) deep). There should be
at least 1 inch (2.5 cm) between the
MLS-310
’s heat
-
sink.
4. Cut out the round hole (one large hole and four small
mounting holes) and inset the
MLS-310
from the front
side.
5. Referring to Figure 5, pass through the four M4x50
Screws (with Nut and Washer) into the mounting holes
on the panel from the back side and turn the M4x50
Screws five times.
6. Turn the four Nuts to adjust the tension so that the
MLS-
310
is tight against the mounting surface.
7. Route and secure the connection cable from the
MLS-
310
to the Marine VHF. Connect the WHITE wire of
the connection cable to the marine VHF’s positive (+)
external speaker output and the shield of the connection
cable to the negative (–) external speaker connection.
8. Connect the RED wire of the connection cable from
the
MLS-310
to a Positive (+) 12VDC positive source
(capable of supplying 1.5A of current) and the BLACK
wire of the connection cable to Negative (–) 12VDC
source.
o
peratIon
1. Before connecting the
MLS-310
to the radio, turn on
the radio and set the AF VOL level to minimum.
2. Turn the radio off then connect the
MLS-310
to the ra-
dio.
3. Rotate the
MLS-310
volume knob to “12 o’clock” posi
-
tion.
4. Turn the radio on and adjust the
VOL
knob on the radio
to a comfortable listing level
5. After adjusting the volume on the radio, you may adjust
the
MLS-310
volume or turn off the speaker using the
volume knob.
r
eplaceMent
p
arts
Mounting Bracket
(Black):
RA0636400
Mounting Bracket
(White):
RA0636500
Mounting bracket Knobs
(Black):
RA0978600
Mounting bracket Knobs
(White):
RA0978500
Volume knob
(Black):
RA0652800
Volume knob
(White):
RA0635600
Mounting bracket mounting hardware
: U9900147
s
pecIFIcatIons
Supply Voltage
:
13.8 VDC ±15 %
Current Drain
:
1.5 A @13.8 VDC,
VOL Knob MAX,
Audio Input Level: 700mVrms
Audio Input Level
:
700mVrms (Nominal)
1Vrms (Maximum)
Input Impedance
:
1.8 k
(Approx.)
Speaker Impedance
:
8
Audio Output
:
8 W @13.8 VDC, 10% THD
Audio Input Level: 700mVrms
Maximum Audio Output
: 10 W @13.8 VDC,
Audio Input Level: 700mVrms
Operating Temperature
: –4 °F to +140 °F
(–20 °C to +60 °C)
Connection Cable Length
: 6.5 feet (2 m)
Disposal of your Electronic and Electric Equipment
Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.
Electronic and Electric Equipment should be recycled at a facility capable of handling these items
and their waste byproducts.
In EU countries, please contact your local equipment supplier representative or service center for
information about the waste collection system in your country.
Figure 5
Figure 3
Figure 4
Nut
M4 x 50 Screw
Wall thi 1 inch (25 mm)
Washer
Yaesu UK Ltd
Unit 12, Sun Valley Business Park
Winnall Close
Winchester SO23 OLB
United Kingdom
Tel: +44 (0)1962 866667
Fax: +44 (0)1962 856801
Email: [email protected]
Declaration of Conformity
Nr. YUK-DOC-0203-14
We, Yaesu UK Ltd. certify and declare under our sole responsibility that the following equipment
complies with the essential requirements of the Directive 1999/5/EC and 2011/65/EU.
Type of Equipment
Marne Loudspeaker with 10W Amplifier
Brand Name
YAESU
Model Number
MLS-310
Manufacturer
YAESU MUSEN CO. LTD.
Address of Manufacturer
Tennozu Parkside Building, 2-5-8 Higashi-Shinagawa,
Shinagawa-ku, Tokyo, 140-0002 Japan
Applicable Standards:
This equipment is tested to and conforms to the essential requirements of directive, as included
in following standards:
EMC
1999/5/EC Art. 3 (1) (b)
EN61000-6-1:2007
EN61000-6-3:2007+A1:2011
ROHS2
2011/65/EU Art. 7 (b)
EN 50581:2012
The technical documentation as required by the Conformity Assessment procedures is kept at
the following address:
Company
Yaesu UK Ltd
Address
Unit 12, Sun Valley Business Park, Winnall Close
Technical Construction file
Winchester, Hampshire UK SO23 0LB
Issued by:
Yaesu Musen Co. Ltd, Tokyo Japan
File No:
YETA00256
Drawn up in:
Winchester, Hampshire UK
Date:
24
th
February 2014
Signed for and on behalf of Yaesu UK Ltd
Name and position:
PCJ Bigwood
Technical Sales Manager
