manualshive.com logo in svg

XYZ Machine Tools ProTURN SLX 1630, Safety, Installation, Maintenance, Service & Parts List Manual

Share
Download
XYZ Machine Tools ProTURN SLX 1630 Safety, Installation, Maintenance, Service & Parts List Manual Download Page 71

67 

XYZ Machine Tools 

ProTURN SLX 1630 ProtoTRAK SLX CNC Safety, Installation, Service & Parts List Manual

 

 

49 

23337-73  Wiper - Bedway (Left, Rear) 

Rubber 

24-0336 

1 

50 

  

Hexagon Socket Screw 

  

M5x6L 

8 

57 

22446 

Bearing - self aligning 

  

2204E-2RS1TN9 

1 

58 

N04 

Lock Nut 

S45C 

N04(

20x16UNF) 

1 

59 

W04 

Lock Washer 

  

W04 

1 

60 

16295-1 

Bearing Housing 

FC20 

  

1 

61 

  

Socket Head Cap Screw 

  

M12x50L 

4 

62 

  

Washer - Spring 

  

M12 

4 

63 

  

Socket Head Cap Screw 

  

M6x20L 

2 

64 

25-0321 

Bumper 

Rubber 

  

2 

65 

25-0320 

Cam 

SS41 

  

1 

66 

  

Socket Head Cap Screw 

  

M8x70L 

2 

67 

23337-82  Wiper - Bedway (Right, Front) 

Rubber 

25-0335 

1 

68 

24714 

Gib - X Axis 

FC30 

25-0217 

1 

69 

17-0321-00  Screw - Adjusting 

S30C 

  

2 

70 

  

Socket Head Cap Screw 

  

M8x25L 

4 

71 

25-0201 

Saddle 

FC25 

  

1 

72 

  

Socket Head Cap Screw 

  

M12x65L 

4 

73 

23337-81  Wiper - Bedway (Left, Front) 

Rubber 

25-0334 

1 

74 

24704 

Ballscrew - Z Axis 

SCM415 

25-0310 

1 

75 

  

Cover - Bearing 

  

AVH7205 

1 

76 

23940 

Bearing Set - Angular Contact Ball 

  

7205 BECBP 

2 

77 

SLX 16302  Spacer 

S45C 

  

1 

78 

24A-0308  Seat - Bearing 

S45C 

  

1 

79 

  

Socket Head Cap Screw 

  

M8x25L 

4 

80 

16452 

Nut - Clamp 

S45C 

19x16UNF

1 

81 

24A-0216  Cone Clamping Element 

Brass 

  

1 

82 

16983-1 

Pulley-ballscrew 

Aluminum 

  

1 

83 

98481A090  Woodruff Key 

  

#3 (1/8"x1/2") 

1 

84 

W01 

Lock Washer 

  

W01 (

12) 

1 

85 

N01 

Lock Nut 

  

N01 (

12x32UNF) 

1 

86 

  

Set Screw 

  

M5x10L 

3 

87 

  

Socket Head Cap Screw 

  

10-32x3/4" 

1 

88 

  

Socket Head Cap Screw 

  

M12x35L 

4 

89 

400-5M-15  Belt - Z Axis 

  

400-5M-15 

1 

90 

  

Pulley 

Aluminum 

5M-30T 

1 

91 

  

Socket Head Cap Screw 

  

1/4-20UNCx30L 

4 

92 

  

Washer - Flat 

  

1/4" 

4 

93 

  

Washer -Spring 

  

1/4" 

4 

94 

77USDA-0304  Base - Motor - Z Axis 

FC30 

  

1 

95 

24425 

Motor - Z Axis Servo 

  

  

1 

96 

25-0223 

Cover Plate (Front) 

SS41 

  

1 

 

 

 

 

I01153.xls 

 

5.1.15    Headstock Taper Adjustment 

The headstock may be adjusted to remove turning taper if the taper is caused by a 
lack of parallelism of the headstock to the bed ways.  Ensure that the level of the bed 

is correct prior to any headstock adjustments. 

 

To adjust the headstock alignment, loosen the four socket head cap screws that 

attach the headstock housing to the bed.  Using the adjusting screw located at the 

Summary of Contents for ProTURN SLX 1630












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands