Xylem Sontek River Surveyor RS5 User Manual Download Page 127

Page: 127 / 149

SonTek RS5 User Manual (August 2020) 127

Appendix B. Software Settings

B-1.

General Tab

The General Tab contains settings pertaining to general software functionality. The

options are shown and described below:



Language

Automatic languages include: English, French, German, Greek, Italian,

Japanese, Korean, Polish, Portuguese, Portuguese (Brazilian), Romanian,

Russian, Spanish, Spanish (Latin America)



UI Scale

The UI Scale sets the user interface scale for text, buttons, and software

features. The default value is 100%.



Charting Scale

The Charting Scale sets the axis/legend labels for all charts separately.



Data Storage Location

This sets the location where the RSQ files will be saved after a measurement is

collected.

Summary of Contents for Sontek River Surveyor RS5






















































































































































Search results

Summary of Contents for Sontek River Surveyor RS5

Reviews:

Related manuals for Sontek River Surveyor RS5

Brands by name

Popular brands

Xylem Sontek River Surveyor RS5, User Manual

Search results

Summary of Contents for Sontek River Surveyor RS5

Reviews:

Related manuals for Sontek River Surveyor RS5

Brands by name

Popular brands