Xylem SI Analytics TM 235 TO Operating Manual Download

Page: 44 / 48

3) TW 7650

Fig. 86

You have the following options:



Init

»:

Starts a re-initialization of the TW 7650.



Get Vial

»:

Fetches a vial from the changer and places it in the oven.

The sample plate position is queried at the beginning.



Set Vial

»:

Take a vial out of the oven and place it in the changer.

The sample plate position is queried at the beginning.



Head Up

»:

Moves the needle head to the top position.

The gas supply must be switched separately



Head Down

»: Moves the needle head to the lowest position for sampling.

The gas supply must be switched separately.

Error messages

3.4

Error number

Description

Troubleshooting

401

The TO

7280 / TW

7650 is not ready for

operation

Check if the oven is switched on and
the cables are correctly connected to
the titrator and PC?

402

The TO

7280 / TW

7650 is in a non-initialized

state or stop state, e.g. after a work list has been
aborted.

The oven must be reinitialized manually.

404

Due to a device error, the system is in the stop
state.

The oven must be reinitialized manually.
If the error still occurs, please contact
our service department.

405

There is a serious internal device error

Please contact our service.

Summary of Contents for SI Analytics TM 235 TO
















































Search results

Summary of Contents for SI Analytics TM 235 TO

Reviews:

Related manuals for SI Analytics TM 235 TO

Brands by name

Popular brands

Xylem SI Analytics TM 235 TO, Operating Manual

Search results

Summary of Contents for SI Analytics TM 235 TO

Reviews:

Related manuals for SI Analytics TM 235 TO

Brands by name

Popular brands