7
Draining The Pressure Tank
WARNING!
Release all air pressure
from the tank before opening the Drain
Valve. Take care when discharging air
through the Safety Valve, Drain Valve
or air Outlets. The discharged air can
cause dust, stones, or any other foreign
particles to be blown through the air at
high pressure.
Air in the compressor tank causes water to
accumulate. This must be drained off frequently to
prevent corrosion and damage to the unit. This should
be performed after each use and prior to the next use.
1. Turn the drain valve plug anti-clockwise (when
viewed from the bottom of the tank) to open it.
FIG.
E
2. Allow all of the water in the tank to drain out.
3. Replace the drain valve plug and turn it clockwise
to tighten it.
Note:
The tank will not pressurise while the drain
valve is open.
Cleaning The Air Filters
The air filters prevent dust and dirt being drawn in. It is
essential to clean these filters at least after every 100
hours in service. Clogged air filters will decrease the
performance of the compressor dramatically.
1. Allow the compressor to run and build up
pressurised air in the tank. Once the motor has
stopped running, turn the compressor off and
disconnect it from the power supply.
2. With an air hose and blow gun connected to
the regulated pressure outlet, turn the pressure
regulator until the regulated pressure gauge shows
a pressure of around 3bar.
3. Undo the screw on the cover of the air filter unit and
lift off plastic cover.
4. Remove the filter sponge from the housing, tap it
and spray it with the blow gun to remove any dirt.
Re-insert it into the housing.
5. Re-attach the lid and replace the screw.
Changing The Oil
The oil should be refilled for the first time after 100
hours of operation. Thereafter, the oil should be
drained and refilled after every 500 hours of service.
1. Release any accumulated air pressure from the tank
and ensure that it is disconnected from the power
supply.
2. Remove the oil drainage screw and use a vessel to
collect the oil from the unit as it drains out.
FIG. F
Note:
if the oil does not drain out completely, the
compressor may be tilted slightly to facilitate this.
3. Re-attach the oil drainage screw.
4. Remove the oil sealing plug and fill the pump with
oil up to the required level (approximately 200ml).
SAE 5W/40 oil or an alternative of the same quality
is recommended.
5. Replace the oil sealing plug.
6. Dispose of the old oil in a responsible manner by
taking it to an old oil drop off point. Check with your
local council for more information. DO NOT dispose
of old oil down the drain.
WARRANTY
YOUR WARRANTY FORM SHOULD BE RETAINED
BY YOU AT ALL TIMES. IN ORDER TO MAKE A
CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO YOUR NEAREST
BUNNINGS WAREHOUSE WITH YOUR BUNNINGS
REGISTER RECEIPT. PRIOR TO RETURNING YOUR
PRODUCT FOR WARRANTY. PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE
RELATING TO THE WARRANTY POLICY OR
PROCEDURE.
The benefits provided under this warranty are in
addition to other rights and remedies which are
available to you at law.
Our goods come with guarantees that cannot be
excluded at law. You are entitled to a replacement or
refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs
associated with a claim under this warranty, however,
where you have suffered any additional direct loss as a
result of a defective product you may be able to claim
such expenses by contacting our customer service
helpline above.
1 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 12 months
from the original date of purchase and is intended for
DIY (Do It Yourself) use only. If a product is defective
it will be replaced in accordance with the terms of this
warranty. Warranty excludes consumable parts, for
example: driver bits.
Ozito Industries Pty. Ltd.
25 Fox Drive, Dandenong South, Victoria, Australia
3175
WARNING
The following actions will result in the warranty being
void.
• Professional, Industrial or high frequency use.
• If the tool has been operated on a supply voltage
other than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any
way.