Xtralis VESDA LCD Programmer Hand Held Product Manual Download Page 24 | Manualshive

Page: 24 / 54

background image

Xtralis VESDA LCD Programmer Product Guide

Xtralis

VESDA

®

18

www.xtralis.com

33.

Relay Startup Mode

- Displays the energize/de-energized condition for each relay.

If required, use the

+ -

and

keys to change the energized/de-energized state of

relays.

ADM

34.

Latching

- This screen displays the latched/unlatched relay condition for different

levels of alarms and faults. In the latched condition the reporting of an alarm or a
fault continues to be reported even after the event is over. Manual intervention is
necessary to reset. If the condition is unlatched the reporting of the condition
automatically stops once the event is over. To latch an alarm or a fault place a

against the respective alarm level or fault. The isolate function is fixed for
unlatched and cannot be changed.

ADM

Scrn
No.

Description

Min.
Access
Level

↵

Parameter

Default

Relay Startup Mode

Relay 2 & 3 energized

Energized

Relays 1, 4-7 (4-12)

Energized

Parameter

Default

Latching

Sector (1-4)

N/A

Fire 2

Latched

Fire 1

Latched

Alert

Latched

Scanning N/A

Urgent Fault

Latched

Minor Fault

Latched

Isolate

Unlatched

«
...
22
23
24
25
26
...
»

Summary of Contents for LCD Programmer Hand Held























































Reviews:

No comments

Related manuals for LCD Programmer Hand Held

Brand: Zapi Pages: 50

Brand: JETWAY Pages: 46

Brand: ASROCK Pages: 95

Brand: Zamel Pages: 2

Brand: Gigabyte Pages: 76

Brand: Texas Instruments Pages: 11

Brand: ASROCK Pages: 26

8A 72QFN Series

Brand: IDT Pages: 29

Brand: National Semiconductor Pages: 22

Brand: Gigabyte Pages: 112

Brand: Texas Instruments Pages: 17

Qseven conga-QA5

Brand: Congatec Pages: 61

Brand: Engbo Pages: 64

Brand: IEI Technology Pages: 194

STEVAL-IHM011V1

Brand: ST Pages: 27

S2257 THUNDER 2400

Brand: TYAN Pages: 105

Brand: Texas Instruments Pages: 14

Brand: DFI Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands