Xtralis VESDA LCD Programmer Hand Held Product Manual Download Page 44

Page: 44 / 54

Xtralis VESDA LCD Programmer Product Guide

Xtralis

VESDA

www.xtralis.com

122.

Miscellaneous

•

Isolate remind - Provides an option to enable or disable the Beeper reminder for
Isolate function

•

Latch Alarms - This provides a YES/NO option to latch/unlatch all Alarms

•

Latch Faults - This provides a YES/NO option to latch/unlatch all Faults

ADM

123.

LCD Programmer

- Select the LCD Programmer and press

USR

124.

Status

- Displays the current status for:

•

Current User Level

•

Current Access Level

•

Faults

•

Software Version Installed

•

Configuration Code

USR

125.

Address (Zone) Number

- If the LCD Programmer has been allocated a Address

(Zone) Number, it is displayed in this screen. This is only for VLS.

ADM

126.

Location

- Allocate a VESDA Zone name and location and assign these to the

LCD Programmer.

ADM

127.

Power Supply Number

- Input the number of the power supply that is assigned to

the detector. If the VESDA Intelligent power supply is not being used enter “0”.

ADM

128.

Address Control Lockout

- This screen allows you to lock or unlock the button

functions on any Display in the VESDA Zone. This stops someone logging on at an
OPERATOR level from using the zone control or system control function. The
buttons controlled are:

•

Mode/Test

•

Silence/Scan

•

Reset

•

Isolate

ADM

129.

Factory Defaults

•

Factory Defaults - To restore factory defaults, highlight Restore and press

•

Defaults OK - Highlighting Start and pressing

will acknowledge Factory

Default settings and clear faults 12, 30, 31, 33, 34, 35, 38, 57, 68 and 72.

DST

ADM

Scrn
No.

Description

Min.
Access
Level

Parameter

Default

Isolate Remind

Enabled

Latch Alarm

Enabled

Latch Fault

Enabled

↵

Summary of Contents for LCD Programmer Hand Held























































Search results

Summary of Contents for LCD Programmer Hand Held

Reviews:

Related manuals for LCD Programmer Hand Held

Brands by name

Popular brands

Xtralis VESDA LCD Programmer Hand Held, Product Manual

Search results

Summary of Contents for LCD Programmer Hand Held

Reviews:

Related manuals for LCD Programmer Hand Held

Brands by name

Popular brands