Xtrails VESDA-E VEP-A00 Product Manual Download Page 72 | Manualshive

Page: 72 / 109

background image

VESDA-E VEP-A00-P Product Guide

64

www.xtralis.com

Function

State Change

Use Night-time
Threshold

Unmonitored GPI

l

The detector uses night-time
thresholds while ≥ 5 VDC.

Monitored GPI

l

The detector uses night-time
thresholds while the contact is
closed.

Note:

While the GPI is off (contact
open, voltage ≤ 2V), the day or
night thresholds are determined
according to the internal clock
and the configuration of the
detector (using Xtralis VSC).

0V

5V

Night

Day or Night

Day or Night

Open

Closed

Night

Day or Night

Day or Night

Reset + Disable

Unmonitored GPI

l

Detector resets on a 0 VDC to 5 VDC
rising edge and on 5 VDC to 0 VDC
falling edge, and;

l

Detector is held disabled while ≥
5 VDC.

l

Detector is enabled on a 5 VDC
to 0 VDC falling edge.

Monitored GPI

l

The detector resets on closure or
opening of the contact, and;

l

The detector is held disabled
while contact is closed.

l

The detector is enabled when
the contact opens.

0V

5V

Reset and
enabled

Disabled

Reset

Open

Closed

Disabled

Reset

Reset and
enabled

Inverted Reset

Unmonitored GPI

l

The detector resets on a 5 VDC to 0
VDC falling edge.

Monitored GPI

l

The detector resets on the opening of
the contact.

0V

5V

Reset

Open

Closed

Reset

Table 5-3: GPI Operation (continued...)

Notes:

l

When using the standby or disable options it is recommended that all remote displays on VESDAnet are
configured to have the Isolate button locked out.

l

When the detector is disabled or set to standby via the GPI, the status cannot be changed through the
normal enable / disable function on the front panel or via Xtralis VSC or a remote display. Refer to
Section 2.3.2 on page 6 for further information.

l

When the night-time thresholds are invoked via the GPI, the clock settings for day-start and night-start
are overridden.

«
...
70
71
72
73
74
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

Brand: LEXIBOOK Pages: 9

Brand: Radio Shack Pages: 12

Brand: Bellman & Symfon Pages: 4

Brand: Salusfin Pages: 5

Brand: Prestige Pages: 12

Brand: Sharp Pages: 1

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: jablotron Pages: 2

Brand: IKEA Pages: 36

EDA-R5000 Zerio plus

Brand: Electro Detectors Pages: 3

CT-SMZW2007-FBR

Brand: Hioth Pages: 6

Brand: Barbeques Galore Pages: 21

Brand: HumanTechnik Pages: 40

Brand: Prestige Pages: 8

Brand: Hyundai Pages: 12

Brand: Polarstart Pages: 7

Brand: Avital Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands