Xtrails VESDA-E VEP-A00 Product Manual Download | Manualshive

Page: 53 / 109

background image

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

45

5

Configuration

This chapter describes a number of configuration options, user functions and security features of the VEP-
A00 detector that the installer and users must to be familiar with. These include:

l

defining connections and connecting to the detector

l

security

l

detector commands

l

configuration options

l

relay options

l

GPI functions

l

default settings

The VEP-A00 detector is initially configured using Xtralis VSC software installed on a PC directly connected
to the USB port. It is necessary to connect to the detector in order to configure it. The procedure for
connecting to the detector is described in Section 5.1.1 below.

5.1

Communication between Xtralis VSC and the detector

In order to allow communication between Xtralis VSC and the detector, the following steps must be
performed:

1. Define a USB Connection Profile and then connect to the detector using USB (See Sections 5.1.1, 5.1.2

and "Adding a USB Connection" below).

2. If using Ethernet as a permanent connection method, then:

l

configure the respective parameters in the detector, including the authentication password.

l

create a connection profile for Ethernet as required.

l

connect to the detector.

USB is used for initial configuration, however it must not be used for permanent connection. Permanent
connection for secondary monitoring must only be done with Ethernet.

For example, the installer would connect directly to a VEP-A00 using the USB port with a laptop running
Xtralis VSC in order to configure the detector to enable Ethernet, the parameters of which could be unique for
each installation. A connection profile would need to be defined for the temporary USB connection, and then
for the permanent connection using VESDAnet, Ethernet.

Note:

Refer to the VESDA Communications Guide for further information.

5.1.1

Defining Connection Profiles in Xtralis VSC

There are multiple ways to connect to a VEP-A00 detector. Each connection method requires a range of
information. This information is saved in a connection profile in the Xtralis VSC Connection Manager, which
subsequently enables the user to quickly connect to the detector.

5.1.2

Connection Profile for a Detector

To define a connection to a VEP-A00 detector connected to the PC or laptop via USB, Ethernet, follow this
procedure:

1. In Xtralis VSC, select

Connection | Manager

from the menu system.

The Connection Manager dialog is displayed (Figure 5-1).

«
...
51
52
53
54
55
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

Brand: Gentex Pages: 6

Brand: GPX Pages: 2

Brand: Greenheck Pages: 7

SmartThings ADT Smoke Alarm

Brand: Samsung Pages: 34

Brand: NUTRICHEF Pages: 6

Brand: Automate Pages: 35

Brand: Automate Pages: 40

Brand: CrimeStopper Pages: 32

Brand: Bush Baby Pages: 32

Brand: Axley Pages: 18

Brand: Hochiki Pages: 2

Brand: Avital Pages: 21

Brand: Avital Pages: 34

Brand: La Crosse Technology Pages: 10

Brand: Daewoo Pages: 4

Brand: La Crosse Technology Pages: 13

Brand: Quell Pages: 17

Brand: Pandora Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands