Xtrails VESDA-E VEP-A00 Product Manual Download | Manualshive

Page: 40 / 109

background image

VESDA-E VEP-A00-P Product Guide

32

www.xtralis.com

4.3

Wiring

The screw type terminals located on electrical terminals within the VEP-A00 detector will accept wire sizes
from 0.2 mm² to 2.5 mm² (24 – 14 AWG).

Refer to Codes and Standards Information for Air Sampling Smoke Detection on page iii for code specific
requirements.

Refer to the VESDA System Design Manual for cabling details.

Note:

The VEP-A00 detector is IP 40 rated, therefore a suitable cable gland or conduit must be used to
maintain the IP rating. (The IP rating is not UL tested.)

Caution:

Electrostatic discharge (ESD) precautions need to be taken prior to removing the fascia from
the detector in order to prevent damage to sensitive electronic components within the VEP-A00.

Attention :

Les precausions contre le decharge electrostatique dois etre respecter avant d’ouvrir le panneau
du detecteur afin de prevenir au dommage des composants electroniques a l’interieur du VEP-
A00.

4.3.1

Cabling Inlets

The VESDA-E VEP-A00 contains four inlets for power, relay and network cabling, located on the upper and
lower sides of the detector base. The holes have a diameter of 26 mm (1.02 inch).

Note:

To maintain the specified IP rating, cable glands or conduit must be used.

Figure 4-32: Cabling Inlets

«
...
38
39
40
41
42
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

Brand: Techno Line Pages: 102

Brand: AcuRite Pages: 4

Brand: ETT Pages: 6

Brand: HMC Pages: 23

Brand: bolid Pages: 2

Brand: Xtralis Pages: 2

Brand: Spencer Pages: 44

Brand: Naxa Pages: 10

Brand: DEI Pages: 37

Brand: DEI Pages: 40

Brand: Clas Ohlson Pages: 2

Brand: DEI Pages: 20

Brand: Universal Pages: 6

Brand: AFRISO Pages: 20

Brand: Scarlett Pages: 6

Edwards Genesis WG4RF-SVMC

Brand: UTC Fire and Security Pages: 4

Brand: Magicar Pages: 60

Brand: Hama Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands