Xtrails VESDA-E VEP-A00 Product Manual Download | Manualshive

Page: 25 / 109

background image

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

17

4

Installation

The VEP-A00 detector is shipped with the following components:

l

1 VESDA-E VEP-A00 detector

l

Installation Sheet

l

Mounting bracket

l

Mounting template for directly mounting the detector to the mounting surface

l

Exhaust Adaptor (US only)

l

1 End of Line resistor for the monitored GPI

Check all components for damage and refer any concerns to your authorized representative.

Depending on the nature of the installation, it may be necessary to procure the following items:

l

The latest revision of this full product guide can be downloaded from the partner extranet at
www.xtralis.com.

l

A 24 VDC Power Supply and backup battery, compliant with local fire protection codes and standards.

l

Screws and inserts for the mounting bracket that are appropriate for the installation location.

l

Type A to Type B USB Interface Lead, required for initial configuration of the detector (Figure 4-1).

l

Wrist strap for ESD prevention.

Figure 4-1: Type A to Type B USB Interface Lead

4.1

Prepare the Detector

l

Remove tape from the exhaust port.

l

Invert the fascia if required. Refer to Section 4.2.1 for further information.

l

Remove cable and pipe inlet plugs as required. Place a large screwdriver in the large slot and twist (A), or
use a small screwdriver in the side slots (B) to lever the plug out (Figure 4-2). Use the edge of the
detector (C) for a lever point to avoid marking the case.

A

B

C

Figure 4-2: Remove Cable and Pipe Inlet Plugs

«
...
23
24
25
26
27
...
»

Summary of Contents for VESDA-E VEP-A00














































































































Reviews:

No comments

Related manuals for VESDA-E VEP-A00

Brand: Oliver Hemming Pages: 9

Brand: Directed Electronics Pages: 37

Brand: EMC Pages: 2

Brand: Nippon Pages: 10

TRUSENSE SMOKE 2050-DS10

Brand: Kidde Pages: 28

Brand: WOOX Pages: 47

Smart Sound Controlled Cloud Alarm Clock

Brand: MUID Pages: 4

Brand: HumanTechnik Pages: 40

Brand: i-Star Pages: 8

Brand: BEARWARE Pages: 30

Brand: BEARWARE Pages: 32

Brand: Avital Pages: 25

Brand: Mustang Pages: 24

Brand: jablotron Pages: 2

Brand: Rattler Pages: 27

PK 100 Smoker 'N Roaster

Brand: Woodland Pages: 48

Brand: Punkt Pages: 4

Brand: Scorpio Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands