background image

Page 

basiC engine maintenanCe

To keep your engine operating at peak performance there are some basic maintenance procedures that need to be performed on 
your engine on a regular basis:

  After you are finished running the engine for the day, pinch the fuel line to stop the engine.  This will allow the engine to burn any 

excess fuel out of the crankcase.

  Remove the air filter element and wash it thoroughly in warm water and a small amount of liquid detergent.  After it's clean, allow 

it to dry, then reoil it and install it back into the air filter housing.

  Remove the glow plug from the engine and squirt several drops of high-quality after-run oil into the glow plug hole and the carburettor 

opening.  Pull the pull-starter cord several times to distribute the oil throughout the engine, then reinstall the glow plug and copper 

washer.  The after-run oil will prevent the inside of the engine (especially the crankshaft bearings) from rusting.

  Clean the outside of the engine using a stiff brush and 

nitro  car  cleaner,  then  dry  the  engine,  using  a  rag  or 
compressed air.

  Periodically check the condition of the clutch to check 

for wear.

  Periodically oil the clutch bell bearings.

  Check the engine's cylinder head bolts and backplate screws 

after each day of use to ensure that they're tight.  This will 
prevent air leaks from causing erratic engine performance.

Loop four nylon cable ties around 
the corners of the engine's cylinder 
head, making sure that the ratchet 
portion  of  the  cable  ties  are  up 

toward you.  When your xT2 flips 

over, the cable ties will prevent the 
cylinder head from being scratched 
and gouged.

engine tip

instaLLing tHe boDy

step 1:  appLying tHe DeCaLs

  For your convenience, some of the decals have already been applied.  To apply the remaining decals, simply remove the decals 

from the protective backing and adhere them onto the body as you like.

step 2:  instaLLing tHe boDy

  Install the body onto the chassis, using the body clips provided to hold it in place.

  Double-check that the body does not interfere with the wheels, the suspension or the tuned pipe.  If it does, you will need to trim 

the body slightly to fit around those areas.

PRO TIP

  Other than during the break-in period, always make sure that you install the body when driving your XT2.  When your 

xT2 flips over, the body will help protect the chassis and its components.

CHassis tuning guiDe

IMPORTANT

  It's very important when making changes to the settings of your XT2 that you make the settings the same for 

each side.  For example, if you change the spring tension on the right front shock, you should change the spring tension on the 
left front shock the same amount, etc.

Do not make any changes that are more than 3 degrees from the initial settings listed or the handling characteristics of your 

X-Terminator 2 RTR Nitro Buggy will become very poor.

Chassis alignment and geometry are important if you want your X-Terminator 2 RTR Nitro Buggy to perform well.  A good performing 
buggy means a buggy that is easier to drive, too.  Follow our guidelines in this section to get the most out of your XT2.

Summary of Contents for X-Terminator 2





































































Reviews: