background image

MB8.5 Indoor Cycle

9

XTERRA Fitness Indoor Cycling Console Battery Installation:

1.  Remove the battery cover from the back of the computer.

2.  Insert 2 AAA batteries into the battery compartment and reinstall the battery cover.

3.  When Battery working voltage is too low, The “Low battery” indicator will show up on 

the console display indicating it is time to change the batteries.

Speed Sensor Transmitter Battery Installation

1.  Remove the battery cover from the transmitter.

2.  Install 2 AAA batteries in the battery compartment and reinstall the battery cover.

3.  When new batteries are installed in the transmitter or console you must perform the  

synchronizing procedure below for the console to work properly

Synchronizing the transmitter to the console:

After installing the batteries, and before attaching the console and transmitter to the bike, 

you must synchronize the two so they can ‘talk’ to each other.

1.  Press and hold the two keys on the front of the console for about 3 seconds until the 

display shows ID - -

2.  Now press and hold the blue button on the transmitter for 3 seconds and release. The 

console display should show ID 0. NOTE: You must press the blue button within 10 

seconds after the console is showing ID - - otherwise the console will show: ID ER. If 

the console shows this error then restart the procedure again.

3.  It may be necessary to remove and re-install the batteries in both the  

console and transmitter if you continue to receive an error.

Console Installation:

1.  Install the mounting clamp (

2

) to the back of the console (

1

) with the clamp mounting 

screw (

3

).

2.  Install and slightly tighten the thumb screw (

4

) then adjust the console angle for 

optimal visibility. Once the console is adjusted, continue to tighten the screw until it is 

securely  

attached to the handle bar.

Transmitter Installation:

•  Make sure to route the speed sensor wire behind the frame member. Plug the sensor 

wire into the transmitter as shown below

•  Install the transmitter, at the angle shown below, onto the pre-installed Velcro strip 

located on the back of the chain cover. Make sure the sensor wire connection is at 

the top left when mounting the transmitter.

•  Make sure the sensor wire is routed away from the spinning flywheel

Summary of Contents for MB8.5





















Reviews: