13
ATTACHING HANDLE FOR MODEL HK070F
ASSEMBLy CORD WRAP
ASSEMBLy FRAME AND WHEELS MODELS HK125FW/HK-
175FW/HK215FW
assembly
Tools required: Medium phillips screw driver.
1. Align the holes in the upper housing with the 2 holes in the handle.
2. Insert and tighten screws securely with screw driver.
1. Insert tabs on cord wrap into slots in shell support, lining up the holes
on the cord wrap with those on the side cover.
2. Insert and tighten screws securely with screw driver.
Tools required: Medium phillips screw driver, 5/16” open end or
adjustable wrench, needle nose pliers.
1. Slide axle through holes in wheel support frame. Slide wheel bushings
and flat washer (A) on to each end of axle.
2. Slide wheels on to each axle, being sure that the valve stem (if
pneumatic) is to the outside (see Figure 7.).
3. Attach wheel nut to threaded axle and tighten.
4. Place heater on the assembled frame, making sure that the air inlet
end is by the wheels, and the mounting holes on the tank flange of the
heater align with holes in frame.
5. Take the front handle and align the mounting holes with the cor
responding holes in the tank flange/wheel frame. Slide a screw (A)
through the holes and loosely attach a nut. Repeat for the other 3
holes, then fully tighten all 4 screws and nuts.
6. Repeat this process with the rear handle.
nOTE
: The front handle is longer than the rear handle.
MODELS PT-45/70T-KFA ONLY
-
Tools required:
Medium phillips screw driver.
ASSEMBLING HANDLE
1
.
Align the holes in the upper housing with the 2 holes in the
handle as shown in
Figure 6
.
2. Insert and tighten screws securely with screw driver.
ASSEMBLING CORDWRAP
1. Insert tabs on cordwrap into slots in shell support, lining up the
holes on the cordwrap with those on the side cover.
2. Insert and tighten screws securely with screw driver.
MODELS PT-125T/175T/215T-KFA ONLY
-
Tools required:
Medium phillips screw driver, 5/16” open end
or adjustable wrench, needle nose pliers.
ASSEMBLING FRAME AND WHEELS
1. Slide axle through holes in wheel support frame. Slide wheel
bushings and flat washer (A) on to each end of axle.
2. Slide wheels on to each axle, being sure that the valve stem (if
pneumatic) is to the outside (
see Figure 7.
).
3. Attach wheel nut to threaded axle and tighten.
4. Place heater on the assembled frame, making sure that the air
inlet end is by the wheels, and the mounting holes on the tank
flange of the heater align with holes in frame.
5. Take the front handle and align the mounting holes with the
corresponding holes in the tank flange/wheel frame. Slide a
screw (A) through the holes and loosely attach a nut. Repeat
for the other 3 holes, then fully tighten all 4 screws and nuts.
6. Repeat this process with the rear handle
.
NOTE:
The front handle is longer than the rear handle.
ASSEMBLING CORDWRAP
1. Align holes in cordwrap with corresponding holes in rear
handle. Insert screws (B) through holes, attach nuts and
tighten (see
Figure 7.
).
Do not operate heater without support
frame fully assembled to tank.
NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING OR WHILE CONNECTED
TO A POWER SOURCE
© 2012, Pinnacle Products International, Inc.
6
Kerosene User’s Manual
Handle
Screw
Assembly (Continued)
Figure 6:
Attaching Handle for models PT-45 /
70T-KFA
Figure 7
Attaching Handle for models PT-125T /
175T / 215T-KFA
CAUTION
