Xray XT2 Instruction Manual Download Page 3

3

 IMPORTANT NOTES – ELECTRICAL

•  Insulate any exposed electrical wiring (using heat shrink tubing or electrical 

tape)  to  prevent  dangerous  short  circuits.  Take  maximum  care  in  wiring, 

connecting  and  insulating  cables.  Make  sure  cables  are  always  connected 

securely.  Check  connectors  for  if  they  become  loose.  And  if  so,  reconnect 

them securely. Never use R/C models with damaged wires. A damaged wire 

is extremely dangerous, and can cause short-circuits resulting in fire. Please 

have wires repaired at your local hobby shop.

•  Low battery power will result in loss of control. Loss of control can occur due to 

a weak battery in either the transmitter or the receiver. Weak running battery 

may also result in an out of control car if your car‘s receiver power is supplied 

by the running battery. Stop operation immediately if the car starts to slow 

down.

•  When not using RC model, always disconnect and remove battery. 

•  Do not disassemble battery or cut battery cables. If the running battery short-

circuits, approximately 300W of electricity can be discharged, leading to fire 

or burns. Never disassemble battery or cut battery cables.

•  Use  a  recommended  charger  for  the  receiver  and  transmitter  batteries 

and  follow  the  instructions  correctly.  Over-charging,  incorrect  charging,  or 

using inferior chargers can cause the batteries to become dangerously hot. 

Recharge battery when necessary. Continual recharging may damage battery 

and, in the worst case, could build up heat leading to fire. If battery becomes 

extremely hot during recharging, please ask your local hobby shop for check 

and/or repair and/or replacement.

•  Regularly  check  the  charger  for  potential  hazards  such  as  damage  to  the 

cable,  plug,  casing  or  other  defects.  Ensure  that  any  damage  is  rectified 

before using the charger again. Modifying the charger may cause short-circuit 

or overcharging leading to a serious accident. Therefore do not modify the 

charger.

•  Always unplug charger when recharging is finished.

•  Do not recharge battery while battery is still warm. After use, battery retains 

heat. Wait until it cools down before charging. 

•  Do  not  allow  any  metal  part  to  short  circuit  the  receiver  batteries  or  other 

electrical/electronic device on the model.

•  Immediately stop running if your RC model gets wet as may cause short circuit. 

•  Please dispose of batteries responsibly. Never put batteries into fire.

WARRANTY

XRAY guarantees this model kit to be free from defects in both material and 

workmanship  within  30  days  of  purchase.  The  total  monetary  value  under 

warranty  will  in  no  case  exceed  the  cost  of  the  original  kit  purchased.  This 

warranty does not cover any components damaged by use or modification or 

as a result of wear. Part or parts missing from this kit must be reported within 

30 days of purchase. No part or parts will be sent under warranty without proof 

of  purchase.  Should  you  find  a  defective  or  missing  part,  contact  the  local 

distributor. Service and customer support will be provided through local hobby 

store where you have purchased the kit, therefore make sure to purchase any 

XRAY products at your local hobby store. This model racing car is considered 

to be a high-performance racing vehicle. As such this vehicle will be used in 

an extreme range of conditions and situations, all which may cause premature 

wear or failure of any component. XRAY has no control over usage of vehicles 

once they leave the dealer, therefore XRAY can only offer warranty against all 

manufacturer‘s  defects  in  materials,  workmanship,  and  assembly  at  point  of 

sale and before use. No warranties are expressed or implied that cover damage 

caused  by  what  is  considered  normal  use,  or  cover  or  imply  how  long  any 

model  cars‘  components  or  electronic  components  will  last  before  requiring 

replacement.

Due to the high performance level of this model car you will need to periodically 

maintain and replace consumable components. Any and all warranty coverage 

will  not  cover  replacement  of  any  part  or  component  damaged  by  neglect, 

abuse,  or  improper  or  unreasonable  use.  This  includes  but  is  not  limited  to 

damage  from  crashing,  chemical  and/or  water  damage,  excessive  moisture, 

improper  or  no  maintenance,  or  user  modifications  which  compromise  the 

integrity of components. Warranty will not cover components that are considered 

consumable  on  RC  vehicles.  XRAY  does  not  pay  nor  refund  shipping  on  any 

component sent to XRAY or its distributors for warranty. XRAY reserves the right 

to make the final determination of the warranty status of any component or part.

Limitations of Liability

XRAY makes no other warranties expressed or implied. XRAY shall not be liable 

for any loss, injury or damages, whether direct, indirect, special, incidental, or 

consequential, arising from the use, misuse, or abuse of this product and/or any 

product or accessory required to operate this product. In no case shall XRAY‘s 

liability excess the monetary value of this product.

Take adequate safety precautions prior to operating this model. You 

are responsible for this model’s assembly and safe operation.

Disregard  of  the  any  of  the  above  cautions  may  lead  to  accidents, 

personal  injury,  or  property  damage.  XRAY  MODEL  RACING  CARS 

assumes  no  responsibility  for  any  injury,  damage,  or  misuse  of  this 

product  during  assembly  or  operation,  nor  any  addictions  that  may 

arise from the use of this product.

All rights reserved.

QUALITY CERTIFICATE

XRAY MODEL RACING CARS uses only the highest quality materials,  the best 

compounds for molded parts and the most sophisticated manufacturing processes 

of  TQM  (Total  Quality  Management).  We  guarantee  that  all  parts  of  a  newly-

purchased kit are manufactured with the highest regard to quality. However, due 

to the many factors inherent in model racecar competition, we cannot guarantee 

any  parts  once  you  start  racing  the  car.  Products  which  have  been  worn  out, 

abused, neglected or improperly operated will not be covered under warranty. 

We wish you enjoyment of this high-quality and high-performance RC car and 

wish you best success on the track!

In line with our policy of continuous product development, the exact specifications of the kit may 

vary. In the unlikely event of any problems with your new kit, you should contact the model shop 

where you purchased it, quoting the part number.

We do reserve all rights to change any specification without prior notice. All rights reserved.

R/C & BUILDING TIPS

• Make sure all fasteners are properly tightened. Check them periodically.

• Make sure that chassis screws do not protrude from the chassis.

• For the best performance, it is very important that great care is taken to ensure 

the free movement of all parts.

• Clean all ball-bearings so they move very easily and freely.

• Tap or pre-thread the plastic parts when threading screws.

• Self-tapping screws cut threads into the parts when being tightened. Do not use 

excessive force when tightening the self-tapping screws because you may strip 

out  the  thread  in  the  plastic.  We  recommended  you  stop  tightening  a  screw 

when you feel some resistance.

• Ask your local hobby shop for any advice.

Please support your local hobby shop. We at XRAY Model Racing Cars support 

all  local  hobby  dealers.  Therefore  we  ask  you,  if  at  all  possible,  to  purchase 

XRAY products at your hobby dealer and give them your support like we do. If 

you have difficulty finding XRAY products, please check out www.teamxray.com 

to get advice, or contact us via email at [email protected], or contact the XRAY 

distributor in your country.

Summary of Contents for XT2









































Reviews: