5
30 2042
LOWER SUSPENSION HOLDER INTEGRATED ( SET 12)
30 2070
ECCENTRIC NYLON HUB FOR BU COVERS (4+2)
30 3159
SHORT SUSPENSION ARM - REAR LOWER - C-HUB
30 5439
HIGH-PERFORMANCE KEVLAR DRIVE BELT FRONT 3 x 423 MM
30 5442
HIGH-PERFORMANCE KEVLAR DRIVE BELT REAR 3 x 180 MM
30 5514
ALU SOLID LAYSHAFT
30 5570
FIXED PULLEY 16T
30 7311
REAR WISHBONE PIVOT PIN BOTTOM - S. STEEL - C-HUB (2)
30 9035
HIGH-SPEED BALL-BEARING MR95ZZ 5 x 9 x 3 BLUE COVERED (2)
30 9045
HIGH-SPEED BALL-BEARING MR106ZZ 6 x 10 x 3 BLUE COVERED (2)
30 9054
HIGH-SPEED BALL-BEARING 10 x 15 x 4 BLUE COVERED (2)
30 9319
UNIVERSAL SET OF PLASTIC SHIMS
30 9336
HEX SCREW SH M3x12 (10)
30 9343
HEX SCREW SFH M3x6 (10)
30 9354
HEX SCREW SB M3x8 (10)
30 9358
HEX SCREW SB M4x8 (10)
30 9415
E-CLIP 5 (10)
30 9452
PIN 2x10 (10)
30 1119
4-CELL CHASSIS 1/12 GRAPHITE - CNC MACHINED
30 3015
ALU SUSP. ADJUSTABLE BULKHEAD REAR RIGHT
30 3025
ALU SUSP. ADJUSTABLE BULKHEAD REAR LEFT
30 5000
BALL DIFFERENTIAL WITH LABYRINTH DUST COVERS™ - SET
303025
305000
301119
303015
309319
309054
307311
305514
309343
309035
302070
305442
303159
309319
302042
305358
309415
305570
309452
305439
309336
302042
309354
309045
2. REAR TRANSMISSION
BAG
02
➋
➊
➌
➌
309054
BB 10x15
309045
BB 6x10
309035
BB 5x9
TToo ttiigghhtteenn rreeaarr bbeelltt::
Rotate rear nylon hubs in arrow direction ((AA))
TToo lloooosseenn rreeaarr bbeelltt::
Rotate rear nylon hubs in arrow direction ((BB))
A
B
TToo rreem
moovvee hhoollddeerr,, pprreessss oouutt
w
wiitthh ttooooll aass sshhoow
wnn..
INITIAL POSITION:
PLACE TAB
IN THIS NOTCH
➍
➍
Open Holder
(hole)
Closed Holder
(no hole)
1
1..
Press the plastic holders for the small ball-bearings into the rear
bulkheads. The flange on each holder goes toward the INSIDE of the
bulkhead.
The holder with a hole through it goes into the RIGHT bulkhead.
The holder without a hole through it goes into the LEFT bulkhead.
2
2..
Press a #309045 (BB 6x10) ball-bearing into the open plastic
holder (with hole) in the RIGHT bulkhead. Press a #309035 (BB 5x9)
ball-bearing into the closed plastic holder (without hole) in the LEFT
bulkhead.
3
3..
Press the large eccentric ball-bearing holders into the bulkheads.
Align the tab of each holder with the middle notch in each bulkhead
as shown. It may take some effort to press the large holders into the
bulkheads.
4
4..
Press #309054 (BB 10x15) ball-bearings into the eccentric holders.
Make sure all bearings turn freely and easily.
➊
➋
F
RONT
DETAIL
DETAIL
BELT TENSION ADJUSTMENT
