background image

2

BEFORE YOU START

The NT18 is a high-quality, 1/18-scale nitro touring car intended for persons aged 
16 years and older with previous experience building and operating RC model 
racing cars. This is not a toy; it is a precision car model. This model racing car is 
not intended for use by beginners, inexperienced customers, or by children without 
direct supervision of a responsible, knowledgeable adult. If you do not fulfi ll  these 
requirements, please return the kit in unused and unassembled form back to the 
shop where you have purchased it. Before building and operating your NT18, YOU 
MUST read through all of the operating instructions and instruction manual and fully 

understand them to get the maximum enjoyment and prevent unnecessary damage. 
Read carefully and fully understand the instructions before beginning assembly.

Make sure you review this entire manual, the included engine instructions, and examine 
all details carefully. If for some reason you decide the NT18 is not what you wanted or 
expected, do not continue any further. Your hobby dealer cannot accept your NT18 kit 
for return or exchange after it has been partially or fully assembled.

Contents of the box may differ from pictures. In line with our policy of continuous 
product development, the exact specifi cations of the kit may vary without prior notice. 

CUSTOMER SUPPORT 

XRAY Europe

Pred Polom 762
91101 Trenčín
Slovakia, EUROPE
Phone: 421-32-7440180
Fax: 421-32-7440179
Email: [email protected]

We have made every effort to make these instructions as easy to understand as possible. 
However, if you have any diffi culties, problems, or questions, please do not hesitate to 
contact the XRAY support team at [email protected]. Also, please visit our Web site 
at www.teamxray.com to fi nd the latest updates, set-up information, option parts, and 
many other goodies. We pride ourselves on taking excellent care of our customers.

You can join thousands of  XRAY fans and enthusiasts in our online community at:  

www.teamxray.com

XRAY USA

RCAmerica, 167 Turtle Creek Boulevard Suite C      
Dallas, Texas 75207
USA
Phone: (800) 519-7221 * (214) 744-2400
Fax: (214) 744-2401
Email: [email protected]

SAFETY PRECAUTIONS

WARNING: This product contains a chemical known to the state of California to cause 
cancer and birth defects or other reproductive harm.

When building, using and/or operating this model always wear protective glasses 
and gloves.

Take appropriate safety precautions prior to operating this model. You are responsible 
for this model‘s assembly and safe operation! Please read the instruction manual before 
building and operating this model and follow all safety precautions. Always keep the 
instruction manual at hand for quick reference, even after completing the assembly. 
Use only genuine and original authentic XRAY parts for maximum performance. Using 
any third party parts on this model will void guaranty immediately.

Improper operation may cause personal and/or property damage. XRAY and 
its  distributors have no control over damage resulting from shipping, improper 
construction, or improper usage. XRAY assumes and accepts no responsibility for 
personal and/or property damages resulting from the use of improper building 
materials, equipment and operations. By purchasing any item produced by XRAY, 
the buyer expressly warrants that he/she is in compliance with all applicable federal, 
state and local laws and regulation regarding the purchase, ownership and use of the 
item. The buyer expressly agrees to indemnify and hold harmless XRAY for all claims 
resulting directly or indirectly from the purchase, ownership or use of the product. By 
the act of assembling or operating this product, the user accepts all resulting liability. 
If the buyer is not prepared to accept this liability, then he/she should return this kit in 
new, unassembled, and unused condition to the place of purchase.

Failure to follow these instructions will be considered as abuse and/or neglect.

In line with our policy of continuous product development, the exact specifications of the kit may vary. In the unlikely 
event of any problems with your new kit, you should contact the model shop where you purchased it, quoting the part 
number. We do reserve all rights to change any specification without prior notice. All rights reserved.

Summary of Contents for NT18











































Reviews: