background image

14

/

16

Error Codes

When the e-bike electronic control system fails, the display will automatically flicker the LED

light to indicate the error code.Below is the error codes list.

Error Showing

Error

Note

Light 1 flickers

Open Throttle Fault

Throttle has not returned to the start position on

start-up. Check to see if the throttle can return to

the start position or if there is something blocking

the throttle unit. Contact technical support.

Light 2 flickers

Throttle Fault

Throttle may be damaged. Check the throttle or

throttle cable for damage.

Contact technical support.

Light 1 and light 2

flicker

Over Voltage Protection

The battery voltage is too high to operate.

Incorrect battery was used on the bike.

Check to be sure that the correct battery is being

used on the bike. Contact technical support.

Light 3 flickers

Motor Hall Signal Fault

At least one of the motor’s hall sensor wires have

been disconnected or damaged.

Disconnect and reconnect the motor cable.

Contact technical support.

Light 1 and light 3

flicker

Motor Phase Line Fault

At least one of the motor’s phase wires has been

disconnected or damaged.

Contact technical support.

Light 2 and light 3

flicker

Temperature Sensor

Fault

The controller’s temperature sensor has become

disconnected or damaged.

Contact technical support.

Light 1,light 2 and

light 3 flicker

Current Sensor Fault

The controller’s current sensor has become

disconnected or damaged.

Contact technical support.

Light 4 flickers

Speed Sensor Fault

Re-plug motor cable connector.

Contact technical support.

All light flicker

Communication Fault

Poor connection between the controller and the

display. Check all cable connectors. Check for

corrosion damage. Contact technical support.

Summary of Contents for Beach Cruiser

















Reviews: