Xreg
Xreg V5
USER MANUAL
Brushless Electronic Speed Controller
Xreg
Xreg
V5
Introduction
CAUTIONS
Thank you for purchasing this product! For avoiding any possible troubles
that you may have in use, please take time to read through this manual before
the use. In addition, please note the use conditions and technical parameters
of this product.
ATTENTION
01
USER MANUAL
LED PROGRAM CARD
This LED Program card is for programming TOPMODEL XPower Xreg V5 and HOBBYWING brushless ESCs. Its
friendly interface makes the ESC programming easy and quick. It’s compact and applicable for field use.
Specifications
02
Applications
03
Functions & Explanations
04
• Working Voltage: 4.8-8.4V
• Size: 88 x 58 x 14mm
• Weight: 40g
This LED Program Card works with the following products:
• TOPMODEL XPower Xreg V5 series of brushless aircraft ESCs.
• PLATINUM V1/V2 series & FLYFUN V5 series of brushless aircraft ESCs.
Note 1:
• This program card only works with TOPMODEL XPower Xreg V5 series and HOBBYWING brushless ESCs; it’s
not compatible with other ESCs.
05
User Guide
LED display
for displaying
programmable items
LED display
for displaying
parameter values
ITEM Button
VALUE Button
OK Button
RESET Button
Programming Port
Port for connecting external power supply
(i.e. battery/UBEC)
After all the connections, please connect a battery to your ESC and turn it on. A few seconds later, the LED Program Box will display current settings in your ESC. If the program box doesn’t display anything, then please check if the
programming cable and the wire (on UBEC/that extra battery) for powering LED Program Box have been reversely plugged in. After confirmed all the connections (are correct), disconnect the battery, 2 seconds later, re-connect it
to your ESC to see if any information is displayed on the LED Program Box.
Attention! It often takes a few seconds before LED Program Box displays “digits/information”.
Warning! The battery must be disconnected from your ESC before connecting it to this program box. Otherwise, your ESC cannot be “connected” to the program box.
The way to connect LED program box to ESC may vary due to different ESC hardware design. The following are the ways to connect a LED program box to different ESCs, about which way you should take, please refer to the user
manual of your ESC.
1) For ESC with the throttle cable and programming cable multiplexed
• For ESC with built-in BEC: plug the ESC throttle cable in the port marked with ” on your program box.
• For ESC without built-in BEC (so-called OPTO version): plug the ESC throttle cable in the port marked with and an extra battery (with voltage of 4.8-8.4V) in the other port marked with on your
program box (for powering the program box).
2) For ESC that the fan port (on the ESC) is also the programming port
In this case, please unplug the fan wire (from the FAN/PRG port on your ESC) and then plug one end of the programming cable (included in the product box) in and the other end in the programming port marked with
on your program box.
3) For ESC with a separate programming cable
• For ESC with the programming cable which has output voltage of 4.8-8.4V: plug the programming cable in the port marked with on your program box.
• For ESC with the programming cable which has no output voltage: plug the programming cable in the port marked with and an extra battery (with voltage of 4.8-8.4V) in the other port marked with
on your program box.
4) For ESC with a separate programming port
In this case, please plug one end of the programming cable (included in the product box) in the programming port (on your ESC) and the other end in the port marked with on your program box.
Note 2:
1) In general, the separate programming cable mentioned above is the “shorter” cable with a JR connector on your ESC.
2) The extra battery mentioned above can also be replaced by an UBEC.
How to connect this LED Program Box to different ESCs
1
How to make LED Program Box work
2
• ITEM Button: press this “ITEM” button can select the programmable item(s) you want to adjust/check; the corresponding (item) number of each item will be displayed on the left LED display.
• VALUE Button
：
after selected one programmable item, the corresponding parameter stored in your ESC will be displayed on the right LED display; and press this “VALUE” button can adjust parameter values.
• OK Button: press this “OK” button after you adjust all the parameters (you want to adjust), a Red “——” will show up on the right LED display for about 1 or 2 second(s) to indicate it’s transferring the new parameter
values to your ESC. This Red “——” will disappear when the ESC saves all the parameter values.
• RESET Button: press this “RESET” button can factory reset you ESC.
How to program your ESC with a LED Program Box
3
©JAN 2018 V1.0
Importé et distribué par:
TOPMODEL
S.A.S.
Le jardin d’entreprises de sologne
41300 SELLES-SAINT-DENIS
FRANCE
www.topmodel.fr
BOÎTIER DE PROGRAMMATION
