background image

15 

signal types.   

Picture too bright and there is 
distortion in the brightest area   

 

Check if the contrast setting is too high. 

 

Possibly the output quality of DVD broadcaster is set too 
high. 

 

It maybe also due to improper terminal connection of the 
video frequency signal in a certain position of the system. 

Picture is whitish or too bright in the 
darkest area of the picture 

 

Check if the setting for the brightness is too high 

 

Possibly the brightness grade of DVD player (broadcaster) 
is set too high. 

No picture or signal produced from 
the displayer if “XXX in search” 
appears. 

 

Check if the cable is disconnected. 

 

Check if it’s connected to the proper terminal or if the input 
mode is correct. 

There appears an indication - 
“outside the receivable scope) 

 

Check if the TV set can receive input signal. The signal is 
not correctly identified and VGA format is beyond the 
specified scope. 

Remote control cannot work 
properly 

 

Check if the batteries are installed in the reverse order. 

 

Check if the battery is effective. 

 

Check the distance or angle from the monitor. 

 

Check if there is any obstruct between the remote control 
and the TV set. 

 

Check if the remote control signal- receiving window is 
exposed to strong fluorescence.   

No picture and sound, but only 

hash. 

 

Check if the antenna cable is correctly connected, or if it 
has received the video signal correctly.     

Blur picture 

 

Check if the antenna cable is correctly connected. 

 

Of if it has received the right video signal. 

No sound 

 

Check if the “mute” audio frequency setting is selected. 

 

Check if the sound volume is set to minimum. 

 

Make sure the earphone is not connected. 

 

Check if the cable connection is loose. 

When playing VHS picture search 
tape, there are lines at the top or 
bottom of the picture. 

 

When being played or in pause VHS picture search tape 
sometimes can’t provide stable picture, which may lead to 
incorrect display of the liquid crystal TV, In this case please 
press “auto” key on the remote control so as to enable the 
liquid crystal TV set to recheck the signal and then to 
display correct picture signal 

 

Summary of Contents for LC-26HU36S






































Reviews: