background image

NON-COMBUSTIBLE CONSTRUCTION

Your XO griddle is designed easy placement in a non-combustible structure such as an island 

or similar outdoor structure built of masonry or Hardibacker.  

In such an installation, the griddle has a perimeter flange that rests on the countertop allowing 

the unit to simply slide into place in the prepared cutout.  No additional fastening is required.   

Do not grout the unit in place.  This allows easy removal for future service or maintenance.  

In such installations where the surrounding materials used are non-combustible, a minimum 

clearance of 12” must be maintained on either side and 5” behind the griddle.

WHEN COMBUSTIBLE CONSTRUCTION MATERIALS ARE PRESENT

 

Combustible materials are defined here as anything which will ignite, melt, emit smoke and/or

fumes or be deformed by heat.

If combustible construction materials are present in the vicinity of the griddle such as wooden 

framing, vinyl or wooden siding, etc .  -  a minimum clearance of 18” must be maintained in all  

directions from

 

    the griddle 

AND the unit must be installed using an XOG30JACKET

 insulated 

liner.   The cutout dimensions are increased to accommodate the liner which is placed without 

fastening into the cutout.  The liner is supported by a perimeter flange which rests upon the 

countertop and the griddle rests upon that flange.

OVERHEAD CLEARANCE

also be overhan

Minimum overhead clearance (above cooking surface)

60” to Non-Combustible overhead.

Hood must extend a minimum of 3” on all sides of

the cooking area.

Hood must have a flow rate of 1000 CFM minimum.

Hood must be connected to a dedicated GFI 

protected circuit. 

All other minimum clearances must be observed.

Combustible Overhead Construction Must Be 

Protected By An Approved Hood.

Use Of An Approved Hood Is Highly Recommended

With Non-Combustible Overhead Construction.

 

ging or overarching structures which must be taken into account.

griddle location  

(continued)

12

5”

min.

30” to 36”

60”

minimum above 

         cooking surface to 

  non-combustible overhead 

 

We recommend oversizing the hood by 3" on 

each side to maximize efficiency and capture 

space

For example; 

A 30" Griddle would require a 36" Hood

 

NON-COMBUSTIBLE

BACKSPLASH

REAR 

W

ALL

OVERHEAD CONSTRUCTION

Non-Combustible Construction

Sides    12”  Back     5”

Combustible Construction

Sides    18”       Back    18” 

   

Summary of Contents for XOGRIDDLE30 Series





































Reviews: