Xo FLEX Installation Instructions Manual Download | Manualshive

Page: 41 / 59

background image

XO FLEX – Installation instructions

Installation

41

5.13

CONNECTING 230 V AND THE SUCTION MOTOR

CONNECTING MAINS SUPPLY CABLE

Before connecting the mains supply cable to the unit, route the wires three (3) times through the
ferrite as shown below:

Figure 55 – Mains supply cable with ferrite

Connect the mains supply cable to the screw terminals marked J4 with symbols
indicating line (L), neutral (N) and earth

(

)

on the

Mains Board.

«
...
39
40
41
42
43
...
»

Summary of Contents for FLEX




























































Reviews:

No comments

Related manuals for FLEX

Brand: Bartscher Pages: 22

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: Bahco Pages: 9

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Raven Pages: 12

Brand: Zero 88 Pages: 20

Brand: Kapriol Pages: 32

Brand: Cabletron Systems Pages: 33

Brand: i-CAT Pages: 32

Brand: Mackie Pages: 34

Brand: Mackworth Pages: 38

Brand: P&P Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands