XMACHINES Lorei Quick Start Manual Download Page 11 | Manualshive

Page: 11 / 19

background image

b. Place the glass bed over the steel bed and secure them using the

four metal clips. Place the clips at the edge of the bed so that two
are facing away from the printer and two are facing towards the
tower of the printer.

i.

Also note that the larger side of the clips should be on the
metal, not the glass.

«
...
9
10
11
12
13
...
»

Summary of Contents for Lorei




















Reviews:

No comments

Related manuals for Lorei

Brand: DataCard Pages: 8

Brand: Samsung Pages: 341

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brand: Samsung Pages: 15

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 227

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 118

CLP 300N - Network-ready Color Laser Printer

Brand: Samsung Pages: 94

3561ND - B/W Laser Printer

Brand: Samsung Pages: 252

3561ND - B/W Laser Printer

Brand: Samsung Pages: 127

2252W - Printer - B/W

Brand: Samsung Pages: 201

ML 2851ND - B/W Laser Printer

Brand: Samsung Pages: 89

Brand: Oki Pages: 104

Brand: Oki Pages: 108

Brand: Oki Pages: 2

Brand: Oki Pages: 94

Brand: Oki Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands