XMA Viglen Omnino Pro Assembly Manual Download | Manualshive

Page: 23 / 60

background image

0115 846 4000

[email protected]

© 2019 XMA Ltd. All Rights Reserved

8.5 Assembly of Security Pillar Kit (Part 2)

Procedure:

1. Firmly hold the assembled stand raiser with security pillar attached.
2. Feed the security pillar through the stand base cavity. Ensure stand raiser is aligned with three

base clips located in the stand base cavity.

3.  Fit the assembled stand to the Omnino Pro.
4.  Feed the security pillar with chassis attached through the hole on the desired desk.
5.  Secure it with pillar washer and pillar nut
6.  Use padlock to secure the unit.

«
...
21
22
23
24
25
...
»

Summary of Contents for Viglen Omnino Pro





























































Reviews:

No comments

Related manuals for Viglen Omnino Pro

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 8

Dynapro ET 3200 Series

Brand: 3M Pages: 23

ARK-3531 Series

Brand: Advantech Pages: 84

Getting Started Guide

Brand: E.E.P.D. Pages: 96

Brand: Advantech Pages: 17

Brand: Steinberg Pages: 820

Brand: Stahl Pages: 24

Brand: Acer Pages: 61

Brand: Acer Pages: 24

Brand: Acer Pages: 32

Brand: Acer Pages: 32

Brand: Acer Pages: 29

Aspire 7100 System

Brand: Acer Pages: 108

Brand: Acer Pages: 108

Brand: Acer Pages: 130

Altos G330 Series

Brand: Acer Pages: 134

Aspire 1820PT Series

Brand: Acer Pages: 216

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands