Figure (K)
Figure (L)
Computer Mount
Torpedo Mount
M5 Lock Washer
M5 Nylon Insert Lock Nut
M5 Flat Washer
M5X16 mm Screw
M5X15mm Washer
DIRECTION OF BIKE
Figure (O)
Figure (I)
WARRANTY
VEE CAGE
– Limited 1 Year
MINI MOUNT ALUM
– Limited 2 Year
TORPEDO BOTTLE
– Limited 1 Year
All Other Parts – Limited 6 Months
With
Figure (J)
Figure (M)
Figure (N)
Without
STEP 2 BOTTLE INSTALL
1.
EASY INSTALL
. Rotate the bottle clockwise approximately 1/2 inch. Push rearwards, ensuring the rear tab of the
cage slides into the rear bottle recess. Next ensure the rear cage screw head clicks into the long recess on
the bottom of the bottle.
The rear cage tab should now sit against the vertical surface inside the back of the
bottle.
Figure (I)
Please see video online
www.xlab-usa.com/torpedo-system
2.
DOLPHIN TAIL INSTALL
. Decide if you want to fold your straw or keep it upright. If you decide to keep it upright,
set the
DOLPHIN TAIL
straw retainer and screw aside. In order to fold your straw you will need to use the
DOLPHIN TAIL
straw retainer. Using a 2.5 mm Allen wrench and the supplied M4X20mm screw, attach the
Tail into the top of the bottle. Torque to 10 in. lbs maximum.
Figure (J)
3.
STRAW INSTALL
. Determine which hole is best suited for you. Install the plug from the inside of the bottle. Start the
plug at an angle and push up around the perimeter of plug. Ensure the top of the plug is completely through the hole.
The straw is designed to fit tightly in the straw hole to prevent leaking. To best insert the straw, pinch and fold the
end of the straw while pushing it into the hole. For the straw to be vertical, tuck the end of the straw
behind the groove in the bottom of the bottle.
Figure (K)
If you intend to fold the straw down then
place the bottom of the straw in front of the bottle groove. After each ride, gradually trim the straw to
your optimum length. Be sure to trim the straw opposite the bite valve. The bite valve is permanently
installed in the straw.
4.
LID INSTALL
. The split lid provides the fastest refilling but there may be some splashing over bumps.
The solid lid will be much dryer but there is a very small breather hole that may emit very small
amounts of liquid at times. Choose whichever you prefer. The solid lid has a tether hole.
Put the straw through this hole to avoid losing the lid when refilling.
Figure (L)
STEP 3 COMPUTER INSTALL
The
TORPEDO SYSTEM
is designed to be used with or without a computer in front of the
bottle for optimal visibility and functionality.
Figure (M) & Figure (N)
1. Mount the XLAB
AERO COMPUTER MOUNT
on the nose of the
TORPEDO MINI MOUNT
with the supplied hardware.
2. Place the black 16mm long M5 screw through
AERO COMPUTER MOUNT
, through
the M5X15mm washer, through the M5 lock washer, through the
TORPEDO MOUNT
,
through the M5 flat washer and into the M5 nylon insert lock nut.
Figure (O)
3. The front edge of the computer should sit slightly behind the rider’s wrist. Slide the mount along the slot on the
TORPEDO MOUNT
to accomplish this placement and tighten completely to 30 in. lbs of torque.
STEP 4 BOTTLE CARE
WASH YOUR TORPEDO BOTTLE, STRAW, PLUG, BITE VALVE AND LID EVERY TIME YOU USE IT AND BEFORE INITIAL FIRST USE.
Dishwasher
1. Remove all accessories from the bottle before washing (straw, plug and lids) The
DOLPHIN TAIL
can remain attached.
2. Wash in top rack only.
Hand Wash
1. Not necessary to remove accessories when cleaning by hand.
2. Fill bottle with soapy water.
3. Use one hand to cover the holes on top of the bottle.
4. Shake bottle vigorously.
5. Rinse and repeat.
Straw: Use a long thin brush to clean tube.
M4X20mm
