manualshive.com logo in svg

Xirrus XR Series, User Manual

The Bourgault XR Series is a cutting-edge agricultural machinery that ensures superior efficiency and productivity in the field. To get started swiftly and make the most of this exceptional product, simply visit our website and download the free Quick Start Manual or user manual available.

Share
Download
background image

Wireless Access Point

50

Installing the Wireless AP

IEEE 802.11ac data rates are dependent on the number of spatial streams obtained 
through the use of MU-MIMO, 80 vs. 160MHz channel widths, the number of 
transmit antennas, and the type of modulation. 

Figure 23

 shows the maximum 

data rate achievable at each level, with many additional lower rates occurring at 
each level dependent on signal level, signal to noise ratio in the environment, etc.

Phase 1 802.11ac, first available in consumer products in 2012 and enterprise 
products in 2013, supports up to 80MHz channels and up to 3 spatial streams for a 
maximum data rate of 1.3Gbps.

Phase 2 and beyond products, expected starting in 2014, will add 160MHz 
channels and up to 8 spatial streams for a maximum data rate of 6.9Gbps.

ACExpress™

Xirrus 802.11ac IAPs use ACExpress™ to optimize wireless performance by 
automatically separating faster 802.11ac clients from slower Wi-Fi clients. Since 
Wi-Fi is a shared medium, this separation ensures that slower 802.11a/b/g/n 
clients do not starve the performance of 802.11ac clients. For example, the data 
rate of an 802.11n client is less than 25% of the rate of an 802.11ac client, and thus 
will take four times as much air time for a given amount of data. This takes 
available bandwidth away from faster clients, reducing their performance 
significantly. ACExpress intelligently separates clients by type onto different 
radios, grouping fast clients separately from slow clients, thereby maximizing 
performance for all. ACExpress is supported on all Xirrus 802.11ac products, and 
may be enabled or disabled as part of the Load Balancing feature. See 

Step 26 on 

page 330

.

802.11ac Deployment Considerations

The theoretical data rates shown are just that, theoretical. For 802.11ac 
deployments, numerous factors affect real-world performance. These are some 
important considerations in the deployment of networks that include 802.11ac:

Wireless networks are not wired networks.

 Wired network users who 

share a Gigabit network can expect to  see  bursts  of  up  to  900Mbps, 
depending on their hardware. Maximum Wi-Fi data rates are reduced by 
signaling overhead and media contention. Most 802.11ac users will see 

Summary of Contents for XR Series























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR Series

JBL L220 Instruction Manual preview
L220
Brand: JBL Pages: 8
Magnavox FW391C Instructions Manual preview
FW391C
Brand: Magnavox Pages: 26
Magnavox MRD130 Quick Start Manual preview
MRD130
Brand: Magnavox Pages: 4
Cambridge Audio SX-50 Manual preview
SX-50
Brand: Cambridge Audio Pages: 12
808audio SPKA10 Instructions preview
SPKA10
Brand: 808audio Pages: 2
Abus WIRELESS ALARM SYSTEM User Manual preview
WIRELESS ALARM SYSTEM
Brand: Abus Pages: 14
Abus SHSG10000 Installation And Maintenance Manual preview
SHSG10000
Brand: Abus Pages: 11
Abus SECVEST User Manual preview
SECVEST
Brand: Abus Pages: 82
Abus PLSG10000 User Manual preview
PLSG10000
Brand: Abus Pages: 16
Abus WIRELESS ALARM SYSTEM Installation Instructions Manual preview
WIRELESS ALARM SYSTEM
Brand: Abus Pages: 101
GAI-Tronics 13350 Manual preview
13350
Brand: GAI-Tronics Pages: 5
Gainwise TH-601W Quick Manual preview
TH-601W
Brand: Gainwise Pages: 13
B2 Audio RAGE 6.1 Manual preview
RAGE 6.1
Brand: B2 Audio Pages: 7
EAW KF850zF Specifications preview
KF850zF
Brand: EAW Pages: 4
V-Tec AT27SDTD7-V1 User Manual preview
AT27SDTD7-V1
Brand: V-Tec Pages: 16
Young Shin Electronics 2WSHR LCD User Manual preview
2WSHR LCD
Brand: Young Shin Electronics Pages: 10
OEM Presence Elite PE-620f Installation Manual preview
Presence Elite PE-620f
Brand: OEM Pages: 2
Aiphone DE-UR Installation And Operation Manual preview
DE-UR
Brand: Aiphone Pages: 4

Brands by name

Popular brands

Load more brands