Xinuo XF-1069GF Operation Manual Download Page 47

Page: 47 / 48

GPS Chart Plotter & Echo Sounder

Appendix 2: XF-1069GF Wiring Diagram

The definitions of external interfaces are shown as above:

[1] POWER

[2] NMEA

[3] TD

[4] GPS ANT

Power connector is a 2-pins plug. The red cable is for positive power supply input while the

black (or blue) cable is for the negative power supply input. Connect these two cables to 24V

DC power of the vessel. Please pay attention to the polarity. (Pin 1 as positive and pin 2 as

negative.)

The power interface definitions are shown as right:

1---The positive of the power

2---The negative of the power

Note:

The voltage range of power supply input is DC 10V~36V. Do not exceed this voltage

range, or the device will be damaged. And please make sure to connect the air outlet

tightly.

The data interface definitions are shown as below:

Note:

the pins of 1,2 are the output of GPS signal, the pins of 3,4,5,6 are the output of AIS

signal, the pins of 7,8 are the input of HDT.

Summary of Contents for XF-1069GF

















































Search results

Summary of Contents for XF-1069GF

Reviews:

Related manuals for XF-1069GF

Brands by name

Popular brands

Xinuo XF-1069GF, Operation Manual

Search results

Summary of Contents for XF-1069GF

Reviews:

Related manuals for XF-1069GF

Brands by name

Popular brands