Xilinx Virtex-5 FPGA ML561 Page 48 User Manual Download | Manualshive

Page: 48 / 385

background image

48

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 2:

Clock Management Technology

summarizes the availability of CMTs, DCMs, and PLLs in each Virtex-5 device.

DCM Summary

The Digital Clock Managers (DCMs) in Virtex-5 FPGAs provide a wide range of powerful
clock management features:

•

Clock Deskew

The DCM contains a delay-locked loop (DLL) to completely eliminate clock
distribution delays, by deskewing the DCM's output clocks with respect to the input
clock. The DLL contains delay elements (individual small buffers) and control logic.
The incoming clock drives a chain of delay elements, thus the output of every delay
element represents a version of the incoming clock delayed at a different point.

The control logic contains a phase detector and a delay-line selector. The phase
detector compares the incoming clock signal (CLKIN) against a feedback input
(CLKFB) and steers the delay line selector, essentially adding delay to the output of
DCM until the CLKIN and CLKFB coincide.

Table 2-1:

Available CMT, DCM, and PLL Resources

Device

Number of

CMTs

Available

DCMs

Site Names

XC5VLX20T

1

2

Bottom half:

DCM_ADV_X0Y0, DCM_ADV_X0Y1, PLL_ADV_X0Y0

XC5VLX30
XC5VFX30T
XC5VLX30T
XC5VSX35T

2

4

Bottom half:

DCM_ADV_X0Y0, DCM_ADV_X0Y1, PLL_ADV_X0Y0

Top half:

DCM_ADV_X0Y2, DCM_ADV_X0Y3, PLL_ADV_X0Y1

XC5VLX50
XC5VLX50T
XC5VSX50T
XC5VFX70T
XC5VLX85
XC5VLX85T
XC5VSX95T
XC5VFX100T
XC5VLX110
XC5VLX110T
XC5VFX130T
XC5VTX150T
XC5VLX155
XC5VLX155T
XC5VFX200T
XC5VLX220
XC5VLX220T
XC5VSX240T
XC5VTX240T
XC5VLX330
XC5VLX330T

6

12

Bottom half:

DCM_ADV_X0Y0, DCM_ADV_X0Y1, PLL_ADV_X0Y0

DCM_ADV_X0Y2, DCM_ADV_X0Y3, PLL_ADV_X0Y1

DCM_ADV_X0Y4, DCM_ADV_X0Y5, PLL_ADV_X0Y2

Top half:

DCM_ADV_X0Y6, DCM_ADV_X0Y7, PLL_ADV_X0Y3

DCM_ADV_X0Y8, DCM_ADV_X0Y9, PLL_ADV_X0Y4

DCM_ADV_X0Y10, DCM_ADV_X0Y11, PLL_ADV_X0Y5

«
...
46
47
48
49
50
...
»

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Brand: NXP Semiconductors Pages: 24

Brand: SMART Pages: 15

Brand: Renesas Pages: 20

EZ-Extender Analog 120-Pin Probing Board

Brand: Analog Devices Pages: 29

Seven Solutions WR-ZEN Series

Brand: Orolia Pages: 167

Brand: Eaton Pages: 14

Brand: Aewin Technologies Pages: 86

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

Power System S914

Brand: IBM Pages: 48

Brand: VideoWave Pages: 12

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: ETAS Pages: 68

Brand: Kontron Pages: 14

i.MX 8M Mini LPDDR4 EVK

Brand: NXP Semiconductors Pages: 20

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Brand: Infoblox Pages: 44

Brand: Brickcom Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands