manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

Virtex-5 FPGA User Guide

www.xilinx.com

375

UG190 (v5.0) June 19, 2009

Output Parallel-to-Serial Logic Resources (OSERDES)

DATA_WIDTH Attribute

The DATA_WIDTH attribute defines the parallel data input width of the parallel-to-serial 
converter. The possible values for this attribute depend on the DATA_RATE_OQ attribute. 
When DATA_RATE_OQ is set to SDR, the possible values for the DATA_WIDTH attribute 
are 2, 3, 4, 5, 6, 7, and 8. When DATA_RATE_OQ is set to DDR, the possible values for the 
DATA_WIDTH attribute are 4, 6, 8, and 10.

When the DATA_WIDTH is set to widths larger than six, a pair of OSERDES must be 
configured into a master-slave configuration. See 

“OSERDES Width Expansion.”

SERDES_MODE Attribute

The SERDES_MODE attribute defines whether the OSERDES module is a master or slave 
when using width expansion. The possible values are MASTER and SLAVE. The default 
value is MASTER. See 

“OSERDES Width Expansion.”

TRISTATE_WIDTH Attribute

The TRISTATE_WIDTH attribute defines the parallel 3-state input width of the 3-state 
control parallel-to-serial converter. The possible values for this attribute depend on the 
DATA_RATE_TQ attribute. When DATA_RATE_TQ is set to SDR or BUF, the 
TRISTATE_WIDTH attribute can only be set to 1. When DATA_RATE_TQ is set to DDR, 
the possible values for the TRISTATE_WIDTH attribute is 4.

TRISTATE_WIDTH cannot be set to widths larger than 4. When a DATA_WIDTH is larger 
than four, set the TRISTATE_WIDTH to 1.

OSERDES Clocking Methods

The phase relationship of CLK and CLKDIV is important in the parallel-to-serial 
conversion process. CLK and CLKDIV are (ideally) phase-aligned within a tolerance.

There are several clocking arrangements within the FPGA to help the design meet the 
phase relationship requirements of CLK and CLKDIV. The only valid clocking 
arrangements for the OSERDES are:

•

CLK driven by BUFIO, CLKDIV driven by BUFR

•

CLK driven by DCM, CLKDIV driven by the CLKDV output of the same DCM

•

CLK driven by PLL, CLKDIV driven by CLKOUT[0:5] of same PLL

OSERDES Width Expansion

Two OSERDES modules are used to build a parallel-to-serial converter larger than 6:1. In 
every I/O tile there are two OSERDES modules; one master and one slave. By connecting 
the SHIFTIN ports of the master OSERDES to the SHIFTOUT ports of the slave OSERDES, 
the parallel-to-serial converter can be expanded to up to 10:1(DDR) and 8:1 (SDR). For a 
differential output, the master OSERDES must be on the positive side of the differential 
output pair. When the output is not differential, the output buffer associated with the slave 
OSERDES is not available and can not be used.

When using the OSERDES with width expansion, complementary single-ended standards 
(e.g., DIFF_HSTL and DIFF_SSTL) cannot be used. This is because both OLOGIC blocks in 
an I/O tile are used by the complementary single-ended standards to transmit both legs of 
the signal, leaving no OLOGIC blocks available for width expansion.

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

GE MDS 4710M Setup Manual preview
MDS 4710M
Brand: GE Pages: 6
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Brand: RAIDAGE Pages: 60
IBM 8677 - BladeCenter Rack-mountable - Power Supply Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power Supply
Brand: IBM Pages: 126
Advantech ARK-1380 User Manual preview
ARK-1380
Brand: Advantech Pages: 50
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
Anthem Audio SFD-2 MkIII Jumper Configurations preview
SFD-2 MkIII Jumper
Brand: Anthem Audio Pages: 2
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Brand: PairGain Pages: 80
Lattice Semiconductor LatticeMico GPIO Manual preview
LatticeMico GPIO
Brand: Lattice Semiconductor Pages: 28
Extron electronics VERSATOOLS MTP User Manual preview
VERSATOOLS MTP
Brand: Extron electronics Pages: 19
Moxa Technologies Smartio CP-104UL Quick Installation Manual preview
Smartio CP-104UL
Brand: Moxa Technologies Pages: 2
ST X-NUCLEO-GFX01M Series User Manual preview
X-NUCLEO-GFX01M Series
Brand: ST Pages: 31
MSI TV@nywhere Satellite Install Manual preview
TV@nywhere Satellite
Brand: MSI Pages: 2
MSI MS-7846 Manual preview
MS-7846
Brand: MSI Pages: 182
StarTech.com 4K30-HDMI-CAPTURE Quick Start Manual preview
4K30-HDMI-CAPTURE
Brand: StarTech.com Pages: 2
AudioSource SS One/II Manual preview
SS One/II
Brand: AudioSource Pages: 9
CAMBRIONIX SS15 User Manual preview
SS15
Brand: CAMBRIONIX Pages: 40

Brands by name

Popular brands

Load more brands