Xilinx Virtex-5 FPGA ML561 Page 329 User Manual Download | Manualshive

Page: 329 / 385

background image

Virtex-5 FPGA User Guide

329

UG190 (v5.0) June 19, 2009

Input/Output Delay Element (IODELAY)

IODELAY Attributes

summarizes the IODELAY attributes.

IDELAY_TYPE Attribute

The IDELAY_TYPE attribute sets the type of delay used. The attribute values are
DEFAULT, FIXED, and VARIABLE. When set to DEFAULT, the zero-hold time delay
element is selected. This delay element is used to guarantee non-positive hold times when
global clocks are used without DCMs to capture data (pin-to-pin parameters).

When set to FIXED, the tap-delay value is fixed at the number of taps determined by the
IDELAY_VALUE attribute setting. This value is preset and cannot be changed after
configuration.

When set to VARIABLE, the variable tap delay element is selected. The tap delay can be
incremented by setting CE = 1 and INC = 1, or decremented by CE = 1 and INC = 0. The
increment/decrement operation is synchronous to C, the input clock signal.

IDELAY_VALUE Attribute

The IDELAY_VALUE attribute specifies the initial number of tap delays. The possible
values are any integer from 0 to 63. The default value is zero. The value of the tap delay
reverts to IDELAY_VALUE when the tap delay is reset. In variable mode this attribute
determines the initial setting of the delay line.

Table 7-10:

IODELAY Attribute Summary

Attribute

Value

Default Value

Description

IDELAY_TYPE

String:
DEFAULT,
FIXED, or
VARIABLE

DEFAULT

Sets the type of tap delay line. Default delay is
used to guarantee zero hold times, fixed delay is
used to set a static delay value, and variable delay
is used to dynamically adjust the delay value.

IDELAY_VALUE

Integer: 0 to 63

0

Specifies the fixed number of delay taps in fixed
mode or the initial starting number of taps in
variable mode (input path).

ODELAY_VALUE

Integer: 0 to 63

0

Specifies the fixed number of delay taps (output
path).

HIGH_PERFORMANCE_MODE Boolean: FALSE,

TRUE

TRUE

When TRUE, this attribute reduces the output
jitter. The difference in power consumption is
quantified in the Xilinx Power Estimator tool.

SIGNAL_PATTERN

String: DATA,
CLOCK

DATA

The SIGNAL_PATTERN attribute causes the
timing analyzer to account for the appropriate
amount of delay-chain jitter in the data or clock
path.

REFCLK_FREQUENCY

Real: 190.0 to
210.0

200

IDELAYCTRL reference clock frequency (MHz).

DELAY_SRC

String: I, O, IO, or
DATAIN

DATAIN

I: IODELAY chain input is IDATAIN

O: IODELAY chain input is ODATAIN

IO: IODELAY chain input is IDATAIN and
ODATAIN (controlled by T)

DATAIN: IODELAY chain input is DATAIN

«
...
327
328
329
330
331
...
»

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Brand: XMG Pages: 5

Brand: NAD Pages: 2

Brand: Omnia Pages: 6

SAFETank Series

Brand: Raidon Pages: 49

Brand: Lorex Pages: 186

MegaRAID SATA 300-4XLP

Brand: LSI Pages: 3

Millennium P650

Brand: Matrox Pages: 54

Brand: Waves Pages: 41

Brand: Lanner Pages: 78

Brand: Z3 Technology Pages: 87

InvenSense RoboKit1

Brand: TDK Pages: 13

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: IBM Pages: 64

Brand: Microtek Pages: 25

Brand: Kaya Instruments Pages: 48

cPCIS-1100 Series

Brand: ADLINK Technology Pages: 48

7798 I/SITE LAN

Brand: CSI Pages: 56

Brand: NEC Pages: 170

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands