Xilinx Virtex-5 FPGA ML561 Page 202 User Manual Download | Manualshive

Page: 202 / 385

background image

202

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 5:

Configurable Logic Blocks (CLBs)

Timing Parameters

shows the general slice timing parameters for a majority of the paths in

.

Table 5-7:

General Slice Timing Parameters

Parameter

Function

Description

Combinatorial Delays

T

ILO

(1)

A/B/C/D inputs to A/B/C/D
outputs

Propagation delay from the A/B/C/D inputs of
the slice, through the look-up tables (LUTs), to the
A/B/C/D outputs of the slice (six-input
function).

T

ILO_2

A/B/C/D inputs to
AMUX/CMUX outputs

Propagation delay from the A/B/C/D inputs of
the slice, through the LUTs and
F7AMUX/F7BMUX to the AMUX/CMUX
outputs (seven-input function).

T

ILO_3

A/B/C/D inputs to BMUX
output

Propagation delay from the A/B/C/D inputs of
the slice, through the LUTs, F7AMUX/F7BMUX,
and F8MUX to the BMUX output (eight-input
function).

Sequential Delays

T

CKO

FF Clock (CLK) to
AQ/BQ/CQ/DQ outputs

Time after the clock that data is stable at the
AQ/BQ/CQ/DQ outputs of the slice sequential
elements (configured as a flip-flop).

T

CKLO

Latch Clock (CLK) to
AQ/BQ/CQ/DQ outputs

Time after the clock that data is stable at the
XQ/YQ outputs of the slice sequential elements
(configured as a latch).

Setup and Hold Times for Slice Sequential Elements

(2)

T

DICK

/T

CKDI

AX/BX/CX/DX inputs

Time before/after the CLK that data from the
AX/BX/CX/DX inputs of the slice must be stable
at the D input of the slice sequential elements
(configured as a flip-flop).

T

CECK

/T

CKCE

CE input

Time before/after the CLK that the CE input of
the slice must be stable at the CE input of the slice
sequential elements (configured as a flip-flop).

T

SRCK

/T

CKSR

SR/BY input

Time before/after the CLK that the SR (Set/Reset)
and the BY (Rev) inputs of the slice must be stable
at the SR/Rev inputs of the slice sequential
elements (configured as a flip-flop).

Set/Reset

T

RPW

Minimum Pulse Width for the SR (Set/Reset) and
BY (Rev) pins.

T

RQ

Propagation delay for an asynchronous Set/Reset
of the slice sequential elements. From the SR/BY
inputs to the AQ/BQ/CQ/DQ outputs.

F

TOG

Toggle Frequency – Maximum frequency that a
CLB flip-flop can be clocked: 1 / (T

CH

+ T

CL

).

Notes:

1. This parameter includes a LUT configured as two five-input functions.
2. T

XXCK

= Setup Time (before clock edge), and T

CKXX

= Hold Time (after clock edge).

«
...
200
201
202
203
204
...
»

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Univerge SV8100

Brand: NEC Pages: 44

Brand: Lab.gruppen Pages: 35

Brand: Zhone Pages: 1

ThunderLAN TNETE100A

Brand: Texas Instruments Pages: 179

Brand: SUNRICH TECHNOLOGY Pages: 5

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: IOtech Pages: 16

XM24 Expansion Module

Brand: Avaya Pages: 5

Brand: Seattle Computer Products Pages: 31

Brand: axing Pages: 52

Brand: SSV Embedded Systems Pages: 17

PG-Flex FLC-704

Brand: PairGain Pages: 20

SecPath F50X0 Series

Brand: H3C Pages: 41

Brand: Cooler Master Pages: 4

Brand: Thecus Pages: 148

Brand: Telit Wireless Solutions Pages: 79

Brand: Sun Microsystems Pages: 410

Brand: JCAT Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands