manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

162

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 4:

Block RAM

Block RAM and FIFO ECC Port Descriptions

Table 4-21

 lists and describes the block RAM ECC I/O port names.

Table 4-21:

Block RAM ECC Port Names and Descriptions

Port Name

Direction

Signal Description

DI[63:0]

Input

Data input bus.

DIP[7:0]

Input

Data input parity bus. Used in decode-only mode to input the precalculated ECC 
parity bits.

WRADDR[8:0]

Input

Write address bus.

RDADDR[8:0]

Input

Read address bus.

WREN

Input

Write enable. When WREN = 1, data will be written into memory. When WREN = 0, 
write is disabled

RDEN

Input

Read enable. When RDEN = 1, data will be read from memory. When RDEN = 0, read 
is disabled.

SSR

Input

Not supported when using the block RAM ECC primitive. Always connect to GND.

WRCLK

Input

Clock for write operations.

RDCLK

Input

Clock for read operations.

DO[63:0]

Output

Data output bus.

DOP[7:0]

Output

Data output parity bus. Used in encode-only mode to output the stored ECC parity 
bits.

SBITERR

(1)

Output

Single-bit error status.

DBITERR

(1)

Output

Double-bit error status.

ECCPARITY[7:0]

Output

ECC encoder output bus.

Notes: 

1. Hamming code implemented in the block RAM ECC logic detects one of three conditions: no detectable error, single-bit error 

detected and corrected on DO (but not corrected in the memory), and double-bit error detected without correction. SBITERR and 

DBITERR indicate these three conditions.

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Lab.gruppen NLB 60E Operation Manual preview
NLB 60E
Brand: Lab.gruppen Pages: 35
XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Brand: XMOS Pages: 112
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
OPTO 22 PCI-AC48 User Manual preview
PCI-AC48
Brand: OPTO 22 Pages: 28
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
Keysight Technologies U3024AH10 User'S And Service Manual preview
U3024AH10
Brand: Keysight Technologies Pages: 106
SIIG SATA II-150 PCI Quick Installation Manual preview
SATA II-150 PCI
Brand: SIIG Pages: 16
INGENIA Everest CORE Product Manual preview
Everest CORE
Brand: INGENIA Pages: 58
b&t RTL8720D Instruction Manual preview
RTL8720D
Brand: b&t Pages: 34
DataExpert ATX431 User Manual preview
ATX431
Brand: DataExpert Pages: 48
Asus TeleSky User Manual preview
TeleSky
Brand: Asus Pages: 56
HP StoreOnce 2900 Read Me First preview
StoreOnce 2900
Brand: HP Pages: 4
HP UNDP-1H Installation Manual preview
UNDP-1H
Brand: HP Pages: 48
HP ProLiant DL145 Maintenance And Service Manual preview
ProLiant DL145
Brand: HP Pages: 109
StarTech.com 8STUSBDUP12 Instruction Manual preview
8STUSBDUP12
Brand: StarTech.com Pages: 20
Acorn BBC Master 65C102 User Manual preview
BBC Master 65C102
Brand: Acorn Pages: 16
KWorld DVB-T 355U Faq preview
DVB-T 355U
Brand: KWorld Pages: 27
Powerleap PL-iP3 Manual preview
PL-iP3
Brand: Powerleap Pages: 32

Brands by name

Popular brands

Load more brands