manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

Virtex-5 FPGA User Guide

www.xilinx.com

125

UG190 (v5.0) June 19, 2009

Block RAM Port Signals

Block RAM Port Signals

Each block RAM port operates independently of the other while accessing the same set of 
36K-bit memory cells.

Clock - CLK[A|B]

Each port is fully synchronous with independent clock pins. All port input pins have setup 
time referenced to the port CLK pin. The output data bus has a clock-to-out time 
referenced to the CLK pin. Clock polarity is configurable (rising edge by default).

Enable - EN[A|B]

The enable pin affects the read, write, and set/reset functionality of the port. Ports with an 
inactive enable pin keep the output pins in the previous state and do not write data to the 
memory cells. Enable polarity is configurable (active High by default).

Byte-wide Write Enable - WE[A|B]

To write the content of the data input bus into the addressed memory location, both EN 
and WE must be active within a set-up time before the active clock edge. The output 
latches are loaded or not loaded according to the write configuration (WRITE_FIRST, 
READ_FIRST, NO_CHANGE). When inactive, a read operation occurs, and the contents of 
the memory cells referenced by the address bus appear on the data-out bus, regardless of 
the write mode attribute. Write enable polarity is not configurable (active High).

Register Enable - REGCE[A|B]

The register enable pin (REGCE) controls the optional output register. When the RAM is in 
register mode, REGCE = 1 registers the output into a register at a clock edge. The polarity 
of REGCE is not configurable (active High).

Set/Reset - SSR[A|B]

In latch mode, the SSR pin forces the data output latches, to contain the value SRVAL. See 

“Block RAM Attributes,” page 128

. When the optional output registers are enabled, the 

data output registers can also be forced by the SSR pin to contain the value SRVAL. SSR 
does not affect the latched value. The data output latches or output registers are 
synchronously asserted to 0 or 1, including the parity bit. Each port has an independent 
SRVAL[A|B] attribute of 36 bits. This operation does not affect RAM memory cells and 
does not disturb write operations on the other port. Similar to the read and write 
operation, the set/reset function is active only when the enable pin of the port is active. 
Set/reset polarity is configurable (active High by default).

Address Bus - ADDR[A|B]<13:#><14:#><15:#>

The address bus selects the memory cells for read or write. The data bit width of the port 
determines the required address bus width for a single RAMB18 or RAMB36, as shown in 

Table 4-6

 and 

Table 4-7

.

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
Ratoc Systems SCSI PC Card REX-9530V Product Manual preview
SCSI PC Card REX-9530V
Brand: Ratoc Systems Pages: 30
Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
SeaLevel 7406e User Manual preview
7406e
Brand: SeaLevel Pages: 17
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Brand: e-con Systems Pages: 9
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
East Coast Datacom PDS-1/10G User Manual preview
PDS-1/10G
Brand: East Coast Datacom Pages: 19
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Brand: TVT Digital Pages: 2
Omron NJ501-1300 User Manual preview
NJ501-1300
Brand: Omron Pages: 432
Corsair Hydro H110 Quick Start Manual preview
Hydro H110
Brand: Corsair Pages: 10
NetBurner SBL2e User Manual preview
SBL2e
Brand: NetBurner Pages: 30
NEC N8154-25 User Manual preview
N8154-25
Brand: NEC Pages: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Brand: Renesas Pages: 28
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Brand: Alvarion Pages: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Brand: Beck Pages: 2
Behringer X-MADI Quick Start Manual preview
X-MADI
Brand: Behringer Pages: 15
Williams Sound DW SY 1 User Manual preview
DW SY 1
Brand: Williams Sound Pages: 2
Black Box RM 415A Specifications preview
RM 415A
Brand: Black Box Pages: 1

Brands by name

Popular brands

Load more brands