Xilinx LogiCORE IP Product Manual Download Page 15

Page: 15 / 142

XAUI v12.3 Product Guide

www.xilinx.com

PG053 April 6, 2016

Chapter 2:

Product Specification

Verification

The XAUI core has been verified using both simulation and hardware testing.

Simulation

A highly parameterizable transaction-based simulation test suite was used to verify the

core. Verification tests include:

• Register access over MDIO
• Loss and regain of synchronization
• Loss and regain of alignment
• Frame transmission
• Frame reception
• Clock compensation
• Recovery from error conditions

Hardware Verification

The core has been used in several hardware test platforms within Xilinx. In particular, the

core has been used in a test platform design with the Xilinx

10-Gigabit Ethernet MAC. This

design comprises the MAC, XAUI, a

ping

loopback First In First Out (FIFO), and a test pattern

generator all under embedded processor control. This design has been used for

conformance and interoperability testing at the University of New Hampshire

Interoperability Lab.

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands