manualshive.com logo in svg

Xilinx Kria KV260, User Manual

Share
Download
Xilinx Kria KV260 User Manual Download Page 21

Firmware Update

The firmware update button is the physical SW1/FWUEN push button located on the KV260
Starter Kit carrier card. The button is used to support two features:

1. To force the platform into a recovery mode application during power-on. The recovery

application is described in the 

Ethernet Recovery Tool

 section of this document.

2. Security mechanism to prevent remote update of the boot firmware, without the user being

physically present.

Ethernet Recovery Tool

The Ethernet recovery tool is a small application included in the Xilinx provided KV260 Starter
Kit QSPI image. It provides a simple Ethernet-based interface and application for updating the
boot firmware. This application and interface is initiated by holding the firmware update button
during the power-on sequence. The application uses a fixed IP address of 192.168.0.111. The
following figure shows an overview of the set-up.

Figure 5: Ethernet Recovery Tool Setup

SOM

Carrier Card

RJ45

192.168.0.111

192.168.0.XYZ

Computer

System Under Recovery

X24613-022321

The Ethernet recovery tool provides a mechanism for updating either of the dynamic boot
partitions within the primary boot device if Linux is not functional. If Linux is functional, the
recommendation is to update the boot firmware using the 

xmutil

 boot firmware update

utilities. The associated update content is a Xilinx XCK26 binary boot image captured as

BOOT.BIN

. To support platform recovery, the KV260 Starter Kit factory 

BOOT.BIN

 image is

made available on the Xilinx SOM Getting Started web page. You can also use this tool when
customizing the platforms boot firmware with your own 

BOOT.BIN

 generated through the Xilinx

Vitis and PetaLinux tools.

To use the Ethernet recovery tool, follow these steps:

Chapter 6: Board Reset, Firmware Update, and Recovery

UG1089 (v1.2) July 26, 2022

 

www.xilinx.com

KV260 Starter Kit

 21

Send Feedback

Summary of Contents for Kria KV260



























Reviews:

No comments

Brands by name

Popular brands

Load more brands