Bass! How low can you go?
Welcome to
XFIRE AUDIO
welcome to
Life Amplified!
Congratulations on purchasing one of the finest autosound Signal processors in existence.
The X-Bass Pro is designed to deliver Bass, adding Bass is like breathing life into your autosound system. No matter your choice of music X-Bass Pro
will make you experience your music in an exciting new way.
X-Bass Pro is not only letting you control the level of Bass added to your system, it also restores “lost Bass”. Bass is filtered out of your system to
protect your speakers of being damaged by low frequency energy. Not only is bass filtered out on some tracks in the recording studio but,
many factory audio systems are known for filtering out Bass as well. X-Bass Pro has got you covered here it has the technology to restore the filtered
out low Bass.
And to make it fully compatible to any source unit it excepts High and Low level input signals.
Features
XFIRE AUDIO E-Series processors are the result of XFIRE AUDIO’s commitment to design and build prestine high end car audio building blocks,
for the most scrutinizing car audio enthousiast.
•
Bass restoration circuit.
•
Balanced inputs, except both Low and High level input signals.
•
Active two channel speaker level to line level converter.
•
Auto sensing when high level inputs are used, auto turn on/off for seamless integration with OEM systems.
•
DC Offset / Audio signal, turn on selection switch.
•
Remote output for switching on/off amplifiers.
•
4-channel outputs.
•
Output level selection switch.
•
“Super Wide Range” frequency response.
•
“Direct Device Mount” PCB’s and tight tolerance components for improved signal to noise ratios and superior musical reproduction.
•
Input and output connectors direct PCB mounted ensuring maximum signal transfer.
XFIRE AUDIO E-Series processors for seamless integrated precision driven audio . Hear what you’ve been missing!
This operating manual provides necessary information for the installation and use of your XFIRE AUDIO E-Series processor.
Please read it carefully to insure a lifetime of high fidelty autosound enjoyment.
Specifications
Installation
Actual installation of an E-series processor is not a difficult task. However, it takes a few tools, considerable care and precise attention to the
instructions in this manual. If you doubt that you are up to the task, or your car proves to require special installation skills, we recommend having
the work done by an authorized XFIRE AUDIO installation professional.
Safety instructions
•
Always disconnect the negative (“-”) battery terminal before making any connections in the vehicle.
•
Each E-series processor is designed for use with a 12Volt DC negative ground system.
•
Fuse the positive (“+”) power lead, with the right value fuse, the fuse rating for an E-series processor is 1A.
•
Make sure your source unit is switched off when making input connections to the processor.
•
Inspect your processor mounting location carefully to avoid damaging gas tanks, gas lines, brake or hydraulic lines and electrical wiring.
•
Install the processor in a location where it will have enough ventilation, protection from engine heat, heaters, direct sunlight, rain and dirt.
•
Do not install in the engine compartment.
To get the best performance from your X-Bass Pro we it needs to be installed in between the source unit and amplifier(s), when external active
crossover, equalizer or digital sound processor is used, the X-Bass Pro needs to be installed before it. For the bass restoration to work properly the
X-Bass Pro needs to receive an “unprocessed” signal.
Connections
REMOTE OUTPUT (REM OUT)
This is the connection to turn on and off amplifiers and processors connected to the X-Bass Pro. The output voltage
is 12V DC with max 700mA current.
REMOTE INPUT (REM IN)
This is the connection to turn the processor on and off when the processor is used with low (Line) level inputs.
When a +12V DC voltage is applied to this terminal the processor will switch on, when this voltage is removed the processor will switch off.
Usually this is done by the source unit’s remote output.
GROUND (GND)
Ground connection should be made to the vehicle’s chassis with a clean, bare metal, strong connection keep the length of the
ground wires as short as possible. Always use the same wire thickness as used for the positive 12V DC connection.
POSITIVE (B+)
Positive power connection should be made directly to the vehicle’s battery positive (“+”) terminal. Use the proper wire
thickness and make sure you install an inline fuseholder with the correct fuse rating.
Frequency response
10Hz - 70kHz
Bass frequency adjust
25Hz - 70Hz
Q adjust
0.4 - 15
S/N ratio
>95dB (A-weighted)
Channel separation
>90dB
THD+N
<0.06%
Operating voltage
9 - 16V DC
Stand by current draw
<1mA
Power consumption
150mA
Remote out
700mA Max
Input impedance
20k Ohm
Output impedance
150 Ohm
Output level
2.5V/5V/10V RMS
Dimensions HxWxL
27x90x102mm
_
+
CAR
BATTERY
Remote turn on
Remote out to amplifiers
Ground
Use recommended
fuse rating
!
HEAD UNIT
FUSE
XFIREAUDIO
XFIREAUDIO
