background image

_

+

CAR

BATTERY

Remote turn on

Ground

Use recommended

fuse rating

!

HEAD UNIT

FUSE

Connections

GROUND (-) 

Ground connection should be made to the vehicle’s chassis with a clean, bare metal, strong connec-

tion keep the length of the ground wires as short as possible. Always use the same wire thickness as used for the 

positive 12V DC connection. 

REMOTE INPUT (REM)

 This is the connection to turn the amplifier on and off when the amplifier is used with 

low (Line) level inputs. When a +12V DC voltage is applied to this terminal the amplifier will switch on, when this 

voltage is removed the amplifier will switch off. Usually this is done by the source unit’s remote output. The source 

unit’s remote output lead or power antenna lead will 12V DC when the unit is turned on.

POSITIVE (+12V)

 Positive power connection  should be made directly to the vehicle’s battery positive (“+”) ter-

minal. Use the proper wire thickness (see Power Wiring Connection chart) and make sure you install an inline 

fuseholder within 18 inches of the battery connection, the fuse rating for each E series amplifier is given in the 

specifications. 

E series   

LIFE AMPLIFIED

Summary of Contents for E-6001D













Reviews: