Xerox WorkCentre 5945 User'S Manual And Warranty Download | Manualshive

Page: 687 / 722

background image

General Care and Troubleshooting

WorkCentre

®

5945/5955

User Guide

685

!

WARNING

When replacing consumables do NOT remove the covers or guards that are fastened with screws.
You cannot maintain or service any of the parts that are behind these covers and guards. Do NOT
attempt any maintenance procedure that is NOT specifically described in the documentation sup-
plied with your device.

1. Open the front door on the device.

2. Rotate the orange print cartridge locking lever anti-clockwise until it clicks. The lever is to the

right of the print cartridge unit, which is labelled R2.

3. Locate the blue handle at the top right of the print cartridge and pull it out of the device until

it stops (after about 40 cm or 16").

4. Push the blue handle slowly and gently back into the device again to wipe the print head clean.

5. Pull the blue handle out of the device and push it in again two more times.

6. Rotate the orange print cartridge locking lever clockwise to latch the print cartridge and print

head cleaning tool in place.

7. Close the front door of the device.

Cleaning the Control Panel, Touch Screen, Document Feeder and
Output Trays

Regular cleaning keeps the touch screen, control panel and other device areas free from dust and
dirt.

1. Use a soft, lint-free cloth, lightly dampened with water.

2. Wipe clean the entire area of the control panel, including the touch screen.

3. Wipe clean the document feeder, output trays, paper trays and other outside areas of your

device.

4. Remove any residue with a clean cloth or paper towel.

Storing Paper and Other Media

It is important for optimum printing that paper is stored correctly. Take note of the following when
storing media.

•

Store at ambient temperature. Damp paper may cause problems or poor image quality.

Note:

In most air conditioned offices the ambient (room) temperature and humidity is fairly

constant and is suitable for storing paper. If your office is very warm or humid it’s best to store
the paper in another area where it can be kept between 20-24.5°C at 35-55% relative
humidity. Paper that is not stored near the machine should be left in its’ wrapper by the device
to acclimatise for 1 hour before use (to reduce the chance of the paper curling when heated by
the device).

•

Do not open reams of paper until they are required for use. The ream wrapper contains an inner
lining that protects the paper from moisture.

•

Store on a flat surface to prevent the paper from folding or curling.

•

Stack reams of paper carefully on top of one another to avoid crushing the edges. Do not stack
more than five reams on top of each other.

«
...
685
686
687
688
689
...
»

Summary of Contents for WorkCentre 5945



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WorkCentre 5945

Brand: Lanier Pages: 265

Brand: Oki Pages: 167

Brand: Oki Pages: 116

Brand: Oki Pages: 52

Brand: Oki Pages: 331

Brand: Oki Pages: 36

C5800Ldn Series

Brand: Oki Pages: 143

Brand: Oki Pages: 101

Brand: Oki Pages: 6

Brand: Oki Pages: 36

Brand: Oki Pages: 282

Brand: Oki Pages: 269

Brand: Oki Pages: 36

Brand: Oki Pages: 2

Brand: Oki Pages: 3

Brand: Oki Pages: 6

Brand: Oki Pages: 137

Brand: Oki Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands