Xerox WorkCentre 5945 User'S Manual And Warranty Download Page 12 | Manualshive

Page: 12 / 722

background image

Safety and Regulations

WorkCentre

®

5945/5955

10

User Guide

Emergency Power Off

If any of the following conditions occur, turn off the device immediately switch off the device and
disconnect the power cable(s) from the electrical outlet(s). Contact an authorized Xerox Service
Representative to correct the problem:

•

The device emits unusual odors or makes unusual noises.

•

The power cable is damaged or frayed.

•

A wall panel circuit breaker, fuse, or other safety device has been tripped.

•

Liquid is spilled into the machine.

•

The machine is exposed to water.

•

Any part of the device is damaged.

Disconnect Device

The power cable is the disconnect device for this device. It is attached to the back of the machine
as a plug-in device. To remove all electrical power from the device, disconnect the power cable from
the electrical outlet.

Maintenance Information

!

WARNING

Do not use aerosol cleaners. Aerosol cleaners can be explosive or flammable when used on electro-
mechanical equipment.

•

Any operator device maintenance procedures will be described in the user documentation
supplied with the device.

•

Do not carry out any maintenance on this device which is not described in the customer
documentation.

•

Use supplies and cleaning materials only as directed in the user documentation.

•

Do not remove covers or guards that are fastened with screws. There are no parts behind these
covers that you can maintain or service.

Consumables Information

•

Store all consumables in accordance with the instructions given on the package or container.

•

Keep all consumables away from the reach of children.

•

Never throw toner, toner cartridges or toner containers into an open flame.

•

When handling cartridges, for example ink, fuser, etc. avoid skin or eye contact. Eye contact can
cause irritation and inflammation. Do not attempt to disassemble the cartridge. This can
increase the risk of skin or eye contact.

•

Use a broom or a wet cloth to wipe off spilled toner. Sweep slowly to minimize generation of
dust during clean up. Avoid using a vacuum cleaner. If a vacuum cleaner must be used, the unit
should be designed for combustible dusts (e.g. explosion rated motor and conductive hose).

«
...
10
11
12
13
14
...
»

Summary of Contents for WorkCentre 5945



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WorkCentre 5945

Brand: LabelTac Pages: 2

Aficio MP C6503SP

Brand: Ricoh Pages: 264

ApeoSport C5540I

Brand: Fuji Xerox Pages: 108

Brand: Lexmark Pages: 500

WorkCentre M118i

Brand: Xerox Pages: 5

Compa II Series

Brand: Valentin Pages: 110

Brand: Oki Pages: 255

Pro-LX Pro-LX Laminating Card...

Brand: FARGO electronics Pages: 228

Brand: A&D Pages: 31

SignJet JS310 Series

Brand: GRAPHTEC Pages: 83

Brand: Citizen Pages: 57

WorkCentre XD130DF

Brand: Xerox Pages: 1

Brand: UVP Pages: 22

Brand: Xerox Pages: 109

Brand: Paradise POS Pages: 275

Brand: Source Technologies Pages: 47

Brand: Axiohm Pages: 6

Brand: Lanier Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands