Xerox Phaser 6510 User Manual Download

Page: 226 / 236

Regulatory Information

Basic Regulations

Xerox has tested this printer to electromagnetic emission and immunity standards. These standards are

designed to mitigate interference caused or received by this printer in a typical office environment.

United States FCC Regulations

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance

with

these instructions, it may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his/her own expense.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not approved by Xerox can void the authority of the user

operate this equipment.

Note:

To ensure compliance with Part 15 of the FCC rules, use shielded interface cables.

Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

226

Xerox

Phaser

6510 Color Printer

User Guide

Summary of Contents for Phaser 6510













































































































































































































































Search results

Summary of Contents for Phaser 6510

Reviews:

Related manuals for Phaser 6510

Brands by name

Popular brands

Xerox Phaser 6510, User Manual

Search results

Summary of Contents for Phaser 6510

Reviews:

Related manuals for Phaser 6510

Brands by name

Popular brands