manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 185

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

163

Checking Lead Edge Registration

Note

NVM (Non-Volatile Memory) and NVRAM (Non-Volatile Random 

Access Memory) are synonymous.  NVM is displayed by the 
Control Panel.  NVRAM appears in documented text.

Note

Use only A4 paper or 8.5” x 11” paper and make certain the tray 

being tested is the only tray installed when generating the test 
print.

Checking Lead Edge Registration

1.

Generate a Registration Grid Pattern Test Print, see page 1-155 to set up and page 

1-156 for specifics on Grid Pattern test print launch.

Note

The Grid Pattern test print on your printer may, or may not, 
display edge lines.  If no edge lines appear in your test print, 

simply measure to the end of any line perpendicular to the Lead 
Edge.

2.

Using a metric scale, measure the distance from the lead edge of the test sheet to the 
end of any line, or the edge line.  The distance should be 4.0 mm (+/- 1.5 mm in 

Simplex, +/- 1.9 mm in Duplex), see illustration.  

3.

If the line is /- 1.5 mm from the Lead Edge, the printer is within specification.  
If it is greater than 1.5 mm, refer to line 16 in Table 1-104  “NVRAM Adjustment 

Table,” beginning on page 159 (Lead Edge Registration) for adjustment information.

Note

When checking registration, it is recommended to run test prints 

from all available trays and compare individual results before 
making any adjustments.  Doing this will help you determine 

where any adjustments are required.

Adjusting Lead Edge Registration

1.

Enter Diagnostics Mode, see page 1-154.

2.

Press [1] or [5] until “NVM Lead Edge” appears in the bottom line of the display.

3.

Press [2] or [6] until the tray you wish to adjust appears in the bottom line of the 

display.

4.

When prompted for a password, sequentially press [0], [7],[3], [4] to gain entry.

5.

Press [3] or [7] once to display the current numerical registration setting.

Fig 1-33  Lead Edge Registration

S4525-72

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands